HP HDX
X16-1000: DISASSEMBLING PROCEDURE
How
to remove the Battery
Before
disassembling the computer, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.
Remove the battery:
1. Turn the computer upside down on a flat surface, with the front toward you.
2. Slide the battery release latch 1 to release the battery.
3. Pivot the battery 2 upward and remove it 3 from the computer.
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.
Remove the battery:
1. Turn the computer upside down on a flat surface, with the front toward you.
2. Slide the battery release latch 1 to release the battery.
3. Pivot the battery 2 upward and remove it 3 from the computer.
How
to remove the Optical drive
Before
removing the optical drive, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.
4. Remove the battery
Remove the optical drive:
1. Position the computer with the left side toward you.
2. Remove the Phillips PM2.5×7.0 screw 1 that secures the optical drive to the computer.
3. Insert an unbent paper clip or similar tool into the optical drive tab access 2 and push the tab forward to release the optical drive from the computer.
4. Remove the optical drive 3 from the computer.
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.
4. Remove the battery
Remove the optical drive:
1. Position the computer with the left side toward you.
2. Remove the Phillips PM2.5×7.0 screw 1 that secures the optical drive to the computer.
3. Insert an unbent paper clip or similar tool into the optical drive tab access 2 and push the tab forward to release the optical drive from the computer.
4. Remove the optical drive 3 from the computer.
How
to remove the Hard drive
Before
removing the hard drive, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.
4. Remove the battery
Remove the hard drive:
1. Loosen the four Phillips PM2.5×6.0 captive screws 1 that secure the hard drive cover to the computer.
2. Lift the rear edge of the hard drive cover 2, swing it up and forward, and then remove the cover 3. The hard drive cover is included in the Plastics Kit, spare part number 496477-001.
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.
4. Remove the battery
Remove the hard drive:
1. Loosen the four Phillips PM2.5×6.0 captive screws 1 that secure the hard drive cover to the computer.
2. Lift the rear edge of the hard drive cover 2, swing it up and forward, and then remove the cover 3. The hard drive cover is included in the Plastics Kit, spare part number 496477-001.
3.
Disconnect the hard drive cable 1 from the system board.
4.
Grasp the Mylar tabs 2 on the hard drive and slide the hard drive 3 to the
left.
5. Remove the hard drive from the hard drive bay 4.
5. Remove the hard drive from the hard drive bay 4.
How
to remove the RTC battery
Before
removing the RTC battery, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.
4. Remove the battery
5. Remove the hard drive cover
Remove the RTC battery:
Lift the RTC battery from the socket.
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.
4. Remove the battery
5. Remove the hard drive cover
Remove the RTC battery:
Lift the RTC battery from the socket.
How
to remove the Keyboard
Before
removing the keyboard, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.
4. Remove the battery
5. Remove the switch cover
6. Remove the keyboard cover
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.
4. Remove the battery
5. Remove the switch cover
6. Remove the keyboard cover
Remove
the keyboard:
1. Turn the computer upside down, with the front toward you.
2. Remove the two Phillips PM2.5×7.0 screws that secure the keyboard to the computer.
1. Turn the computer upside down, with the front toward you.
2. Remove the two Phillips PM2.5×7.0 screws that secure the keyboard to the computer.
3.
Turn the computer display-side up, with the front toward you.
4.
Open the computer as far as possible.
5. Remove the Phillips PM2.0×4.0 screw that secures the keyboard to the computer.
5. Remove the Phillips PM2.0×4.0 screw that secures the keyboard to the computer.
6.
Lift the rear edge of the keyboard 1 until it rests at an angle.
7.
Release the keyboard 2 by sliding it back to disengage the tabs on the front
edge of the keyboard from the top cover and rest it on the display.
8.
Release the zero insertion force (ZIF) connector 1 to which the keyboard cable
is attached and disconnect the keyboard cable 2 from the system board.
