HP 2760p
EliteBook: DISASSEMBLING PROCEDURE
How
to remove Battery
Before
disassembling the computer, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then unplugging the AC adapter from the computer.
Remove the battery:
1. Turn the computer upside-down on a flat surface, with the battery bay toward you.
2. Slide the battery release latch to release the battery.
3. Pivot the edge of the battery upward and remove it from the computer.
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then unplugging the AC adapter from the computer.
Remove the battery:
1. Turn the computer upside-down on a flat surface, with the battery bay toward you.
2. Slide the battery release latch to release the battery.
3. Pivot the edge of the battery upward and remove it from the computer.
How
to remove Service access cover
Before
removing the service access cover, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then unplugging the AC adapter from the computer.
4. Remove the battery
Remove the service access cover:
1. Position the computer upside-down, with the front toward you.
2. Loosen the three Phillips M2.0x3.0 captive screws that secure the service access cover to the computer.
3. Lift the rear edge of the service access cover until it rests at an angle, and then remove the cover.
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then unplugging the AC adapter from the computer.
4. Remove the battery
Remove the service access cover:
1. Position the computer upside-down, with the front toward you.
2. Loosen the three Phillips M2.0x3.0 captive screws that secure the service access cover to the computer.
3. Lift the rear edge of the service access cover until it rests at an angle, and then remove the cover.
How
to remove Hard drive
Before
removing the hard drive, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then unplugging the AC adapter from the computer.
4. Remove the following components:
a. Remove the battery
b. Remove the service access cover .
Remove the hard drive:
1. Loosen the Phillips M2.5×8.0 captive screw (1) that secures the hard drive bracket to the computer.
2. Grasp the tab on the hard drive and slide it forward to disconnect the hard drive.
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then unplugging the AC adapter from the computer.
4. Remove the following components:
a. Remove the battery
b. Remove the service access cover .
Remove the hard drive:
1. Loosen the Phillips M2.5×8.0 captive screw (1) that secures the hard drive bracket to the computer.
2. Grasp the tab on the hard drive and slide it forward to disconnect the hard drive.
3. Lift
the hard drive (2) to remove it from the computer.
How
to remove Keyboard
Before
removing the keyboard, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then unplugging the AC adapter from the computer.
4. Remove the following components:
a. Remove the battery
b. Remove this service access cover
Remove the keyboard:
1. Turn the computer upside-down, with the front toward you.
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then unplugging the AC adapter from the computer.
4. Remove the following components:
a. Remove the battery
b. Remove this service access cover
Remove the keyboard:
1. Turn the computer upside-down, with the front toward you.
2. Remove
the two screw caps and loosen the five captive screws that secure the
keyboard to the computer.
3. Turn
the computer right-side up, with the front toward you.
4. Open
the display as far as possible.
5. Insert a flat tool under the back edge of the keyboard near the display hinge. Gently lift the rear edge of the keyboard and disconnect the keyboard.
5. Insert a flat tool under the back edge of the keyboard near the display hinge. Gently lift the rear edge of the keyboard and disconnect the keyboard.
6. Holding
the keyboard at an angle, lift the keyboard far enough to gain access to
the cables underneath and release the zero insertion force (ZIF)
connector to which the pointing stick cable is attached to the system
board and remove the pointing stick ZIF cable (3) from the connector.
7. Flip
the keyboard over to the left and lay it flat then release the ZIF
connector that secures the keyboard cable to the system board and remove
the keyboard cable from the ZIF connector.
8. Release
the ZIF connector to which the pointing stick cable is attached, and then
disconnect the cable from the keyboard.
