Toshiba air to water heat pump adjustments, self diagnosis

Hydro Unit
HWS-803XWHM3-E(TR) - HWS-803XWHT6-E(TR) - HWS-803XWHD6-E - HWS-803XWHT9-E - HWS-1403XWHM3-E(TR) - HWS-1403XWHT6-E(TR) - HWS-1403XWHD6-E - HWS-1403XWHT9-E(TR)
Hot Water Cylinder
HWS-1501CSHM3-E(-UK)
HWS-2101CSHM3-E(-UK)
HWS-3001CSHM3-E(-UK)
Outdoor Unit
HWS-803H-E(TR) - HWS-1103H-E(TR) - HWS-1403H-E(TR) - HWS-1103H8-E - HWS-1103H8R-E - HWS-1403H8-E - HWS-1403H8R-E - HWS-1603H8-E - HWS-1603H8R-E

NEW REFRIGERANT (R410A)
This Air to Water Heat Pump adopts a new refrigerant HFC (R410A) to prevent destruction of the ozone layer.  The working pressure of R410A refrigerant is 1.6 times higher than that of the conventional refrigerant R22.The refrigerant oil is also changed for the new refrigeration. Therefore, during installation or service work, be sure that water, dust, former refrigerant, or refrigeration machine oil does not enter the refrigerant cycle of the new type refrigerant Air to Water Heat Pump. A wrong installation or service operation may cause a serious accident.

Method of Defect Diagnosis

In order to diagnose the defective part of the heat pump system, first understand the symptom of the defect.

(1) Check the operation status. (It does not move, or it moves but stops, etc.)

(2) Flashing display on the display part of the hydro unit.

(3) Check the “check code” by the remote control.

Matters to be confirmed first

Check the power supply voltage

Check that the power supply voltage is AC220-230 V± 10 % (signal phase type), AC380-400 V± 10 % (3 phase type). If the power supply voltage is not in this range, it may not operate normally.

Check for any miswiring of the connection cables between the hydro unit and the outdoor unit

The hydro unit and the outdoor unit are connected with three connection cables. Make sure the interconnecting connections between the hydro unit and the outdoor unit terminal blocks are connected to the correct terminal numbers. If not connected correctly, the heat pump system does not operate. However, a miswiring would not cause damage to the equipment.

About the installation of the temperature sensor

If each sensor is removed due to the replacement of the water heat exchange or inverter board, or the replacement of the refrigeration cycle parts, make sure to put the sensor back to the position where it was before.

• Each sensor position has a marking. Make sure to put it back to the exact position.

• Make sure to install it with a sensor holder so that the temperature sensing part of the sensor and the straight part of the copper piping are attached with each other tightly.

• If the installation of the sensor is incomplete or the installed position is wrong, it will not perform a normal control operation and may cause a defect such as a malfunction of the equipment or an occurrence of an abnormal sound, etc.

Non-defective operation (program operation) … No fault code display appears.

In order to control the heat pump unit, there are the following operations as the built-in program operations in the microcomputer. If it does, please understand that the symptom is not a defect of the equipment, and it is an operation necessary for the control and maintenance of the heat pump unit.

How to determine from the check code on the remote control

If the defect is limited by the check code displayed on the remote control

The check codes are separated into two groups: software and hardware errors.

Since a hardware error cannot be cancelled without a part replacement etc., please perform a repair.

If its abnormality is determined, the abnormality is noticed by indicating the check code on the remote control check code display part while sounding off a buzzer.

How to cancel a check code on the remote controller

(1) Press Zone-2 or Hot Water button (on the operation side) to clear the check code.

Press CL to stop a buzzer for an abnormality only.

Although the above procedure cancels the check code, the hardware error will be displayed again until the hardware repair is completed. 

Outdoor Unit Failure Detection

Diagnosis procedure for each check code

• One check code may indicate multiple symptoms. In such a case, see the LED indication on the outdoor board to narrow down the check details.

• The handy remote controller displays a check code only when the same failure repeatedly occurs while the LED on the outdoor board indicates an error even if it occurs only once. This may cause indication inconsistency between the remote controller and LED.

Operation check by PC board switch

Operation check mode

This mode allows to check the operations of the water 2-way valve, water 3-way valve, mixing valve, and circulating pump. This operation is valid when the hydro unit and the outdoor unit are turned on the power.

Operation check mode

(1) Preparation

1) Turn all of the remote controls "OFF" for the hot water supply and heating.

2) Turn off the hydro unit and the outdoor unit.

3) Remove the front panel of the hydro unit.

4) Set SW06_2 "ON"

(2) Operation check

1) Turn on the hydro unit and the outdoor unit.

2) Rotate switch DIP SW01 to position "1" and press tactile switch SW07 for 5 sec. or longer.

3) Rotating the rotary SW01 allows to check each operation.

4) Set the DIP SW06_2 "OFF" to finish.

How to reset hydro function code
If the hydro unit PCB has been replaced, it is necessary to change the FC 01 (capacity setting)
(1) Preparation
1) Turn all of the remote controls "OFF" for the hot water supply [HOTWATER] and heating [ZONE1,2].
2) Turn off the power supply of the hydro unit and the outdoor unit.
3) Remove the front panel of the hydro unit and cover to the hydro unit electrical box.
4) Set SW06_1 

Procedure
1) Turn on the power supply of the hydro unit and the outdoor unit.
• The small yellow LED located near the MCU should be flashing slowly.
2) Press tactile switch SW07 until the yellow LED turns off.
• When the tactile switch SW07 has been press for 5 sec, flashing becomes quickly. And when the switch will be pressed further 5 sec, the yellow LED will turn off.
When the SW07 is released, the yellow LED start to flash quickly again.
3) Turn off the power supply of the hydro unit and the outdoor unit.
4) Set SW06_1 and _2 to "OFF".
5) Replace the electrical box cover and front panel on the hydro unit.

How to reset remote controller function code

It is not possible to reset the remote controller function code setting back to the default values.

Frost Protection Setting

This setting keeps a room with weak heating when users are not home for long hours.

1 Press the ZONE1,2 [Power] button to start a heating operation.

(This is available only for a normal heating operation.)

(No frost protection setting is provided to hot water supply and cooling.)

2 Pressing the FORST PROTECTION button displays the symbol and "F" for temperature setting. 

The heating operation of 15°C is set.In FC_3B in 2-2 section, the set temperature can be changed in the range of 10 to 20°C.

3 Pressing the FORST PROTECTION button makes

disappear, and the set temperature returns to the normal heating temperature. (Pressing the ZONE1,2 [Power] button ends both the frost protection and the heating operation.)

How to release child lock – how to clean the pump filter – Bush Washing machines A126Q and A146Q

Child Lock
Child lock is used in order to protect the washing cycle from the effects of unwanted button activation during the cycle. Child lock is activated by pressing the first and third button
on the control panel at the same time for more than 3 sec. When child the lock is activated, LED’s on the function buttons blink to indicate that child lock is active. In order to deactivate child lock, the same buttons (1st and 3rd) should be pressed again for more than 3 seconds.
Deactivation of child lock is shown by blinking of LED on Start/Pause button.

Pump filter
The pump filter system elongates the life of your pump, which is used to drain the dirty water. It prevents lint to enter the pump. Cleaning of your pump filter in every 2-3 months is
recommended. To clean your pump filter:
Open the kick-plate's cover, by pulling the handle.
Before opening the filter cover, place a cup in front of the filter cover to prevent flow of the remaining water in the machine.
Loosen the filter cover by rotating it counter clockwise and drain the water.
Remove the foreign materials from the filter.
Check for the rotation of the pump manually.
After you have cleaned the pump, fit the filter cover by rotating clockwise.
Put the kick-plate cover into place.
Do not forget that if you do not fit in the filter cover properly, it will leak water.

Detergent drawer

Detergents may form sediments in your detergent drawer or in the housing of the detergent drawer over time. To clean the sediment, pull out the detergent drawer from time to time. To pull out the detergent drawer:

Pull the detergent drawer to the end. 

Keep pulling by pressing on the siphon lid inside the drawer pulled to its end, and remove the drawer from its place. 

Wash with an old toothbrush and copious amount of water.

Remove the leftover disused detergent, avoid dropping it back in to the machine.

After drying the detergent drawer, replace it in the housing by reversing the removal operations.

Siphon plug
Pull out the detergent drawer. Remove the siphon plug and clean the residues of the softener thoroughly. Fit the cleaned siphon plug in its location. Check it is placed properly.

Cabinet
Clean the exterior surface of the cabinet of your machine with lukewarm water and a cleaning substance that will not damage the cabinet.  After rinsing with clean water, wipe it with a soft and dry cloth.

How to program a Poloroid genuine remote control to other devices

Programming procedure of the Poloroid remote control with other devices
The remote lets you control four devices with one easy-to-use, compact unit. After installing batteries, you can program the remote to control your Universal TV, VCR or DVD, Cable or Satellite Receivers, Amplifier or Tuner, and Auxiliary devices. To do so, follow the instructions.
Programming a Device
To control VCR or DVD, Cable or Satellite Receivers, Amplifier or Tuner, and Auxiliary devices, follow these steps. Before proceeding, find the codes for the devices you want to program in “Manufacturer’s Codes” on the right side of this page and write them down or highlight them.
1. Turn on the device (for example, DVD player) and, if needed, load media (for example, a DVD).
2. Press a device key (VCR/DVD, CBL/ SAT, or AUX).
3. Press and hold SET UP until the red LED blinks twice; then release.
4. Enter the first five-digit code for your device. The LED blinks once as each digit is entered. If the code is correct, the LED blinks twice.  [If the LED does not blink twice, repeat steps 2 to 4 and try entering the code again.]
5. Aim the remote at the device and press ‘Power button’. The device should turn off. If it does not, repeat steps 3–5, trying each code for your brand until you find one that works. If you cannot find a code that works, see “Searching for Your Code”.
6. Repeat steps 1–5 for the other devices you want to control. For future reference, write down each working device code below:
AUX Code:
CBL Code:
CD Code:
DVD Code:
SAT Code:
TNR Code:
VCR Code:
7. Press set to save and exit.
Searching for your Code
If your device does not respond to the remote after trying all codes listed for your brand, or if your brand is not listed, try searching for your code:
1. Press a device key once.
2. Press and hold SET UP until the red LED blinks twice; then release.
3. Enter 9-9-1, then the device group number (0= Cable, 1= TV, 2= VCR, 3= Audio).  The LED blinks twice.
4. Aim the remote at the device and press the “Power” . The remote sends IR codes from its  library to the selected device, starting with the most popular code first. If the device responds, go to step 7.
5. If the device does not respond, press CH ▲ . The remote will try the next code.  Continue until the device responds. Press CH ▼ to try the previous code. To search for other device codes, repeat steps 1 to 5.]
6. Press SET UP to save and exit.
Checking the Codes
If you have set up the remote using the procedure in “Searching for Your Code”, you may need to find out which four-digit code is operating your equipment.
[For example, to find out which code is assigned to your TV:]
1. Press TV once.
2. Press and hold SET UP until the red LED blinks twice; then release.
3. Enter 9-9-0. The LED blinks twice.
3. To view the code for the first digit, press 1. Count the LED blinks (for example, three blinks = 3), and write down the number in the appropriate code listing in step 8 under “Programming a Device”. [If a code digit is 0, the LED does not blink.]
4. Repeat step 4 for the four remaining digits, using 2 for the second digit, 3 for the third digit, 4 for the fourth digit, and 5 for the fifth digit.
Changing Volume Lock
The remote comes preset to allow independent volume control of each selected device (Global Volume Unlock). However, you may change the Volume Lock setting to Global Volume Lock so that one device’s volume will control volume in all other modes. After that, you can perform Individual Volume Unlock on a selected device to set its volume control for independent operation or Global Volume Unlock to remove all volume locking.
1. Press and hold SET UP until the red LED blinks twice; then release.
2. Enter 9-9-3 and then press the mode key for the device you want to control volume (for example, TV). The LED blinks twice. Now when you press VOL+, VOL-, or Mute, the selected device (for example, TV) will control the volume regardless of the current mode.
Unlocking All Volume Control (Restoring Global Unlock)
1. Press and hold SET UP until the red LED blinks twice; then release.
2. Enter 9-9-3 and then press VOL+. The LED blinks four times.  Volume is now independently controlled for all programmed devices.
Unlocking a Single Device’s Volume Control
1. Press a device key (TV, VCR/DVD, CBL/ SAT, or AUX).
2. Press and hold SET UP until the red LED blinks twice; then release.
3. Enter 9-9-3 and then press VOL-. The LED blinks four times. Volume is now independently controlled for the selected devices.
Problems and solutions
LED does not blink when you press a key:  Replace battery with new AAA size battery.
LED blinks when you press a key, but device does not respond:  Make sure the remote is aimed at your device and is not more than 15 feet away.
LED blinks one long blink:  An entry error has occurred (for example, wrong key):   Try entry sequence again.
Remote does not control devices or commands are not working properly:  Try all listed codes for the device. Make sure the device operates with an infrared remote control.
CH ▲, CH ▼, and LAST do not work for your RCA TV:  Due to RCA design from 1983 to 1987, only the original remote control will operate these functions.
No volume on a device:  See “Changing Volume Lock”.
Channels do not change properly:  If the original remote control required you to press Enter to change channels, press Enter on this remote after entering the channel number.

How to upgrade the Firmware - Sony DPF D70 digital Photo Frame

To upgrade the Firmware
1. Download the latest firmware from the ESI homepage.
2. Copy the firmware (downloaded and decompressed two files) onto the root directory (most significant hierarchy) of the Memory Stick of 8MB or more empty capacity.
3. Install Memory Stick in the Memory Stick slot of this unit before turning on the power supply.
4. Connect AC adaptor of accessory with this unit and push the power button while pushing the [VIEW MODE] button.
5. The screen becomes the confirmation display whether to do the upgrade of the firmware.
Push the [ENTER] button.
6. The upgrade of the firmware starts.  The power supply cuts automatically when ending.
7. Remove Memory Stick from this unit.
CONFIRMATION OF VERSION AND DESTINATION LANGUAGE SETTING
1. Turn on power pushing the power button.
2. Display the menu screen pushing the [MENU] button.
Note: When the demonstration mode display is in the screen, make it to “Date/time setting” display pushing the [MENU] button after the [Clock] button of remote control.
3. Choose "Various settings" with [Dn] button, and push the ENTER button.
4. Choose "System Information” display with [Dn] button, and push the ENTER button.
5. Confirm it is a hoped firmware version, and push the [ENTER] button.
6. Confirm whether it is a display language that corresponds to destination.
To change language, choose "Language settings" and push the ENTER button.
7. Choice language and push the ENTER button.  To erase the menu display, pushing the MENU button.
To Format the internal memory
1. Turn on power pushing the power button.
2. Display the menu screen pushing the [MENU] button.
Note: When the demonstration mode display is in the screen, make it to "Date/time setting" display pushing the [MENU] button after the [Clock] button of remote control.
3. Choose "Various settings" with [Dn] button, and push the [ENTER] button.
4. Choose "Format internal memory" display with [Dn] button, and push the [ENTER] button.
5. The screen of "Format internal memory? All images will be deleted." appears.  Choose "Yes", and push the [ENTER] button.
6. The screen of "Format internal memory completed." appears.  Choose "Yes", and push theNTER] button.

How to update the software - Sharp LL T2020 – LCD Monitor - Troubleshooting

Advanced Super-V and Anti Glare Low Reflection TFT LCD module

Information about the Pivot Software ((Long height/width display

When rotating the display, change the display orientation using Pivot Software.
Compatible operating systems (OS) for the Pivot Software that comes with the monitor:
Windows 98/2000/Me/XP.
Macintosh OS 8.x - 9.1
- Depending on the graphics accelerator, it may be impossible to use Pivot Software, even with a compatible OS.

For production information and inquiries regarding
Pivot Software:
Portrait Displays, Inc.
(http://www.portrait.com)

Installation of Pivot Software
For Windows
1. Quit all applications being used.
2. Load the accessory CD-ROM into the CD-ROM drive of the computer.
3. Open the [My computer] CD-ROM.
4. Double click on the [Pivot] folder.
5. Double click on [SETUP.exe].
6. Click [Next].
7. Choose [I accept the tems in the License Agreement].
8. Click [Next].
9. Input your Customer information [User Name] and [Organization].
10. Click [Next].
11. Click on [Install].
Installation will begin.
12. When the message indicating installation is finished is displayed, click [Next].
13. Click on [Finish].
14. Click on [Yes] and restart the computer.

For Macintosh
1. Quit all applications being used.
2. Load the accessory CD-ROM into the CD-ROM drive of the computer.
3. Open the CD-ROM.
4. Double click on the [Pivot] folder.
5. Select the desired language.
6. Double click on [Install MacPortrait].
7. Drag the [MacPortrait Install] icon onto the desired disk.  Installation will begin.
8. When the message indicating installation is
finished is displayed, click on [Restart].

For Windows
1.Click the right mouse button or click the left mouse button on at the lower right of the screen.
2.Select [Rotate], [Rotate to 0] or [Rotate to 90].

Rotate ..............The display direction switches.
Rotate to 0 .......The display direction is switched to long width.
Rotate to 90 .....The display direction is switched to long height.

For Macintosh
Choose [ROTATE Now] from [Screen emblem] at the lower right of the screen.

Each time [ROTATE Now] is selected, the display direction switches.
Notes:
- Rotation of the display to match the display direction is done manually.
- The display direction on the OSD menu is switched using [OSD PIVOT] on the [MODE SELECT-2] menu.

Installing set-up information and the ICC profile (For Windows)

For Windows2000

Installing monitor set-up information into Windows2000, and setting the monitor's ICC profile as a predetermined value.
This explanation assumes that the CD-ROM drive is "D drive".
1. Load the accessory CD-ROM into the CD-ROM drive of the computer.
2. Click on the [Start] button. From [Settings], choose [Control Panel].
3. Double click on [Display].
4. Click on [Settings], [Advanced] and [Monitor].
5. Click on [Properties], [Driver] and [Update Driver].
6. When [Upgrade Device Driver Wizard] appears, click [Next].
7. Check [Display a list of the known drivers for this device so that I can choose a specific driver] and click [Next].
8. When [Models] is displayed, click on [Have disk], confirm that [Copy manufacturer's files from:] is [D:], and click [OK].
9. Select the monitor from the list displayed and click [Next].
10. Click [Next], confirm that the monitor's name appears on the screen, and click [Finish]. If [The Digital Signature Not Found] appears, click [Yes].
11. Click on [Close].
12. Click [OK], and close the window.

For WindowsMe

Installing monitor set-up information into WindowsMe, and setting the monitor's ICC profile as a predetermined value.
This explanation assumes that the CD-ROM drive is "D drive".
If the "Add new Hardware Wizard" has appeared:
1. Load the accessory CD-ROM into the CD-ROM drive of the computer.
2. Check [Specify the location of the driver [Advanced]] and click [Next].
3. Check [Display a list of all the drivers in a specific location, so you can select the driver you want.], then click [Next].
4. When [Models] is displayed, click on [Have disk], confirm that [Copy manufacturer's files from:] is [D:], and click [OK].
5. Select the monitor details from the list, then click [Next], [Next], and [Finish]. If the "Add new Hardware Wizard" appears, repeat the installation commands beginning from 2 above. 

If the "Add New Hardware Wizard" has not appeared:
1. Load the accessory CD-ROM into the CD-ROM drive of the computer.
2. Click on the [Start] button. From [Settings], choose [Control Panel].
3. Double click on [Display].
4. Click on [Settings], [Advanced] and [Monitor].
5. In [Options], check [Automatically detect Plug & Play monitors] and click on [Change].
6. Check [Specify the location of the driver [Advanced]] and click [Next].
7. Check [Display a list of all the drivers in a specific location, so you can select the driver you want.] and click [Next].
8. When [Models] is displayed, click on [Have disk], confirm that [Copy manufacturer's files from:] is [D:], and click [OK].
9. Select the monitor details, then click [Next], [Next], and [Finish].
10. Check that the monitor details are displayed, then click [Apply].
11. Click [OK], and close the window.

For WindowsXP

Installing monitor set-up information into WindowsXP, and setting the monitor's ICC profile as a predetermined value.
This explanation assumes that the CD-ROM drive is "D drive".
1. Load the accessory CD-ROM into the CD-ROM drive of the computer.
2. Click on the [Start] button. Choose [Control Panel].
3. Switch to Classic View.
4. Double click on [Display].
5. Click on [Settings], [Advanced] and [Monitor].
6. Click on [Properties], [Driver] and [Update Driver].
7. When [Hardware Update Wizard] appears, check [Install from a list or specific location [Advanced]] and click [Next].
8. Check [Don't search. I will choose the driver to install.] and click [Next].
9. Click on [Have Disk], confirm that [Copy manufacturer's files from:] is [D:], and click [OK].
10. Select the monitor from the list displayed and click [Next].
If [has not passed Windows Logo testing...]  appears, click [Continue Anyway].
11. Confirm that the monitor's name appears on the screen.
12. Click on [Finish].
13. Click on [Close].
14. Click [OK], and close the window.

Installing the ICC profile
Installing the monitor’s ICC profile. (If the set-up information has already been installed, so too has the profile, and there is no need to install it.)
This explanation assumes that the CD-ROM drive is "D drive".
1. Load the accessory CD-ROM into the CD-ROM drive of the computer.
2. Click on the [Start] button. From [Settings], choose [Control Panel].
3. Double click on [Display].
4. Click on [Settings] and [Advanced].
5. Click on [General] and from [Compatibility] select [Apply the new display setting without restarting], then click on [Color Management].
6. Click [Add], and select CD-ROM as the file location.
7. Choose the color profile that you would like to install, and click on [Add].
8. Choose the profile and click on [Set As Default].
9. Click [OK], and close the window.
- When using the ICC profile, set as follows:
- [COLOR MODE] [WHITE BALANCE]: [STD]
- [GAMMA] [HUE] [SATURATION]: [0]
- In [6 COLORS] menu, [HUE] and [SATURATION]
for each color: [0]

Troubleshooting
If you think the monitor may be faulty, please check the following points before taking it to be repaired.  If afterwards it still does not work, contact the shop where you purchased the monitor or your nearest Sharp authorized Service Center.

The monitor's florescent tubes have a limited life span.
- If the screen darkens, persistently flickers or does not light up, it may be necessary to replace the florescent tube unit. Inquire at the shop where you purchased the monitor or your nearest Sharp authorized Service Center. (Never attempt this replacement on your own.)
- In the initial period of use, due to the characteristics of florescent tubes the screen may flicker. (This is not a malfunction.) If this happen, check by first turning off the power, then turning it on again.

No image appears on the monitor (Power LED is not lit)
- Is the power cord connected properly? 

No image appears on the monitor (Power LED is lit)
- Is the computer connected properly? (p. 11)
- Is the computer turned on?
- Is the signal’s input terminal switched to the correct one?
- Is [INPUT-1] or [INPUT-2] set correctly?
- Does the computer's signal timing correspond to monitor specifications?
- Is the computer in power-saving mode?

The image appears distorted
- Does the computer's signal timing correspond to monitor specifications?
- If you are using the analog signal, perform automatic adjustment.
- If you can change the refresh rate on the computer you are using, change the value to a lower frequency.

The display section does not rotate
- Is the display rotated in the correct direction?
- If there is not sufficient spare length in the connected cable, it will not be possible to rotate the display.
The display direction is not changed even after rotation of the display.
- The operation of switching the display direction is required.
Control buttons do not work
- Is the adjustment lock on? 

How to set the Vodafone DTR remote to control your television

Find the brand of your television in the Set-up Code section and select the first 4 digit code in the list. Switch on your TV (not on standby).

Press the TV key and release it.

Press and hold down the Now’s Good key until the red LED underneath the TV key lights up twice.

Enter the 4-digit code for your television (the red LED should light up twice after having entered the fourth digit).

Press the Power key and see if you are able to switch off your television.

If your television does not respond, repeat steps with each code listed for your brand. If none of the codes listed for your brand operate your television, or if your brand is not listed, try the code search. 

Switch your television back on by pressing a number key (or CH+) and check if all the functions are working correctly.

Write down the code for your television on the inside of the battery cover  for quick easy reference.

Programming Notes

• If your device does not respond to the remote after trying all codes listed or your brand is not listed in the code list, use the Auto Code Search method to program your remote.
• Sometimes the first code that “works” with your device may operate only a few functions of your device. There may be another code in the code list that performs more functions. Try other codes from the code list for more functionality.

This is a trial and error procedure; and quiet time consuming. You might have to check different codes said for your device.

Code search

If your device does not respond to the DTR remote after having tried all the codes listed for your brand, you can try the Code search. During the Code search you will run through every available code in the DTR remote library. This method may also work if your brand is not listed at all.

Make sure that your television is switched on.

Press the TV key and release it.

Press and hold down the Now’s Good key until the red LED (underneath the TV key) lights up twice.

Press 9 9 1. The red LED will light up twice.

Aim the DTR remote at your device.

Next press power.

Aim the DTR remote at your Television.  Now press CH+ over and over, until your Television turns off.

Every time you press the CH+ key the DTR remote will send out a POWER signal from the next code contained in the PVR library.
You may have to press this key many times (up to 150 times) so please be patient. The Code search can take approximately 15 minutes.
If you skip past a code, you can go to the previous code(s) by pressing the CH- key. Remember to keep pointing the remote at your device during the Code search.

As soon as the device switches off, press Now’s Good key to store this code.

Press the corresponding device key when doing a Code search. If your device does not have a POWER key, press PLAY instead.

How to unlock a TV which displays a red key on the screen.

You will need the original remote to unlock the TV if you aren't sure of the unlock code. If you don't have the original remote, you will need to purchase one.

If you see a blank screen with a red key on the bottom of the screen, press 'Function' and 'Mute' at the same time. This should unlock the channel. This is an option for people who want the TV to stay locked but, want to be able to bypass the lock to watch a certain show or channel. All other channels will remain locked and the TV will fully lock when it is turned off.

Unlock all of the channels on the TV by entering the factory reset code. There are three main reset codes that TV manufacturers set. These are 0711, 6688 and 3308. Try each one until you find the one that works. This will reset the TV to original factory settings. When you do this, you will lose any information that you have stored in the TV, such as favorite channels, automatic timers and the clock. You will have to go through the full initial set up.

How do I remove a child lock on my TV? (Small combination TV models) 

The child lock stops all the keys on the front of the TV from operating.
To Activate/Deactivate Child lock:
1.Use the remote ( cannot deactivate without the remote )
2.Press Menu
3.Press P Down ( channel down button ) Twice till SETUP is highlighted in White
4.Press Volume up once ( this takes you into the setup menu )
5.The CHILD LOCK option is at the top and should be highlighted white.
6.Use the volume up button to select ON or OFF
7.Press MENU button once you have selected ON or OFF.

How to unlock Maxdorf TV with a RC-A07 remote control.

Hold the music button on the remove in for a long time.

How to adjust the screen of LG LCD projection TV

(1) All adjustment mode are entered by pressing the INSTART key on the remote control, after adjustment press the IN-START key to come out.
(2) Compomation of adjustment mode: The first screen composition of pressing IN-START key.

(3) Select menu to adjust(turn to yellow) with using (CH+), (CH-)) key above screen and press the enter key to adjust on the wanting menu.

(4) After being inputed for SUB menu, select the SUB menu with using (CH+),(CH-) key and adjust the value of adjustment with using the volume +,volume -  key.
(5) Press the IN-START key to come out after adjustment, when the screen is appeared, press again to come out the final adjustment mode.

LCD Adjustment - NRS Adjustment
[ When the LCD panel load data on regular pixel using high speed charge/discharge with sample & holder, the drain width of TFT gradually decreases and the non-resistance increases, and comes out regular noise on screen(shows
vertical line by 12 pixel)  This NRS signal is enforced charge/discharge signal so that the ON/OFF time of TFT mode quickly before starting active video signal, H/L level adjustment is possible to each R, G, B.

(1) Required Test Equipment
1) PC Pattern Generator : 16 Step Gray Pattern
2) Fixation Stand
3) Remote Control for Adjustment
4) Circuit thing Jig for Adjustment (Except Driver Board Assy)
(2) Equipment Composition

(3) Preparation for Adjustment
1) Connect PC Pattern Generator with adjustment Jig (Except Drive part of a circuit block)
2) Select a PC Pattern Generator, 16 Gray.
(4) Adjustment Sequence
1) Turn on a adjustment Jig.
2) Select a RGB_PC by pressing Input Select button on Remote Control.
3) Enter to adjustment mode by pressing IN-START button on Remote Control.

4) Select 4. 62352, then ready to adjust 6. RNRSH, 9. GNRSH and 11. BNRSH.
5) Let’s decrease vertical line Noise by using Volume button.
(Input a R, G, B input signal, then adjust it individually)
6) When finishing the adjustment, get out of adjustment mode by pressing IN-START button.

VCOM Adjustment
(1) Required Test Equipments
1) PC PATTERN GENERATOR : Pattern Generator which can generate each R,G,B signal and can observe the FLICKER best.
2) (Fig. 2) Equipment composition
3) Remote Control
4) Circuit thing Jig for Adjustment (Except Driver Board Assy of adjustment model)

(3) Preparation for Adjustment
1) Connect the PC Pattern Generator with circuit thing for adjustment(circuit block except driver part) and adjustment Jig. shown upper Fig
2) Set the PC Pattern generator with displayable format(DTV720p, SVGA 60Hz, XGA 60Hz) and turn on it.
(4) Adjustment Sequence
1) Turn on the adjustment Jig.
2) Select a RGB_PC by pressing Input Select Key on Remote Control.
3) Enter to adjustment mode by pressing IN-START button on Remote Control.
4) Select 4. 62352, then ready to adjust 4. 62352 RVCOM, 7. 62352 GVCOM and 10. 62352 BVCOM.
5) Let’s decrease flicker by using Volume button.
(Input a R, G, B input signal, then adjust it individually)

6) When finishing the adjustment, get out of adjustment mode by pressing IN-START button on Remote Control.

Assembling Adjustment
5-1. Screen Tilt & Keystone Adjustment
(1) Required Test Equipments
1) Six angles wrench and spanner for knob adjustment or fixation
2) XGA output PC
3) Remote Control
(2) Preparation for Adjustment
1) Do not assemble the front panel equipment so that you can adjust the adjustment knob.
2) Turn the TV ON and select input mode to RGB_PC.
3) Connect XGA output terminal to PC input of TV.
4) Select window screen.

(3) Adjustment Sequence
1) Stick the Engine(Fig. 3) to the knob poll for adjustment and
check the key stone & tilt watching TV screen.
2) Rotate left/right adjustment knob below and adjust engine angle.
3) Adjustment adjustment knob of both sides so that the tilt and keystone are to be under the spec. (The gap between max and min : under 4mm)
4) After adjusting like 3), fix the engine with screw for fixation (2EA. adjustment knob and engine fixing screw).

Screen Position Adjustment
(1) Required Test Equipment
A remote control for adjustment
(2) Preparation for Adjustment
1) Connect a power source with TV Set and turn TV Set on.
2) Do heat run for 15 min and over before adjustment.
3) Receive the main/sub signal of company through 13CH by split screen.
(3) Horizontal Position Adjustment
1) Press In-START key on the remote control to enter the adjustment mode.
2) Select 3. RGB Alignment.
3) Select 10. H_position with channel key in adjust mode.
4) Adjust data with using the left/right key on the remote control in order to be left/right symmetry screen. (Three blocks of the most outer block must be located the most outer block.)

Adjustment for Vertical Position
1) Select 16. V_position with channel key in adjust mode.
2) Change the data to summarized upper and down of screen and then press the IN-START button on Remote Control to get out of adjustment mode.

Adjustment of White Balance and Gamma
(1) Required Test Equipments
1) Illuminometer (name of model : CA-100) 1EA > Measure color of projecting screen center [ CA-110(name of model) is possible to measure White Balance and Gamma - leave it 20Cm from screen center
Follow a measurement machine manual to set CA-100 and CA-110 measurement machine.

2) Pattern Generator 1EA —> 16 step Gray Pattern, 64 step Gray Pattern
3) Set Fixation Stand 1EA
4) Remote Control 1EA
5) Circuit thing Jig for adjustment(Except Drive Board Assy of adjustment model)

Programmed Digital Board so that the VDP Test Pattern can output white signal by 1 level form 0 to 255 level.

Preparation for Adjustment
Compose the equipment follow Fig. 2 and place the set on the fixation stand.
1) Select the VDP Test Pattern signal to R1, G1, B1.
2) Press the IN-START key to select 4. 62352 and then select
5. RVREF, 8. GVREF, 12. BVREF in adjust mode.
3) Adjust the luminance of CA100 below 0.75Cd. (The adjustment range is 196~202)
4) Exit adjustment mode by pressing IN-START button on Remote Control.
5) Press the IN-START key on R/C and select 3. 7050 RGB Set.
6) Check the data 1. RContrast, 8. GContrast, 15. BContrast is 515. Otherwise set the data 515 by using volume button.

Adjustment Sequence
1) Output the 255,255,255 signal of VDP Test Pattern, then display the maximum white pattern on screen.
2) Gamma Adjust Mode is display as below when select 5.  Gamma adjust by selecting IN-START key on R/C

3) Change the 16 Step RGB Data to select white balance x=283, y=297(D9300K).
4) Measure the luminace with changed data.
5) Set the every Gamma data of 16 step to 2.2 on the basis of measured luminance data in 3).  (Max luminance *(n1/16)**2.2) — Max luminance : measured luminance data n1 = every step unit when separating signal level to 16 step)
6) Output the 240, 240, 240(15th data in max white output signal level) in the VDP Test Pattern, change the 15th RGB Data value to come out white balance x=283, y=297(D9300K) and measured step luminance in 5).
7) Output the 224, 224, 224(14th data in max white output signal level) in the VDP Test Pattern, change the 14th RGB Data value to come out white balance x=283, y=297(D9300K) and measured step luminance in 5).

8) Output the VDP Test Pattern signal(208/192/176/160/144/128/112/96/80/64/48/32/16) and change the RGB Data value of each step to come out white balance x=283, y=297(D9300K) and measured luminance in 3).

Gamma adjustment manually
This is adjustment (after finish the 3-4) to check whether Gamma/White Balance adjustment are well adjusted and make correction manually.
1) Prepare the PC Pattern Generator which is possible to output R/G/B of 16 step and 64 step Gray Pattern.
2) Equipment composition: Follow Fig. 2.
3) Turn on the Jig for adjustment.
4) Select the RGB_PC by pressing the input select button on Remote Control.
5) Output the 16 Gray Pattern in PC Pattern Generator.  Check it with the naked eye whether Screen Gamma and W/B is right about each Gray.  If it’s not, press the IN-START button on Remote Control and then adjust the level data of each step manually in sub menu of 5. Gamma adjust.
6) Output the 64 Gray Pattern in PC Pattern Generator.  Check it with the naked eye whether Screen Gamma and W/B is right about each Gray or whether there is Gamma noise.  If there’s any problem, adjust in 5).
7) After finishing adjustment, exit adjustment mode by using IN-START button on Remote Control.

White Uniformity Adjustment
(1) Required Test Equipment
1) Uniformity measurement equipment : Equipment which can measure chromaticity in the whole screen
2) Set Stand 1EA
3) Remote Control for Adjustment
4) Circuit thing Jig for Adjustment(Except Driver Board Assy of adjustment model)
Programmed Digital Board so that the VDP Test Pattern can output white signal by 1 level form 0 to 255 level.

Preparation for Adjustment
1) Composite the equipment as shown Fig 2, and place the set on fixation stand.
2) After inputting company channel 13, adjust color uniformity like Horizontal/Vertical position adjustment of input signal part adjustment by using Remote Control for adjustment.
3) After pressing IN-START key on Remote Control for adjustment, select the adjustment mode 6. Uniformity adj.
Refer to register value and correct register value if need.
<Resister Explanation about uniformity adjustment>
1. RamCtrl : s/w saving uniformity write order(Do not adjust)
2. CSHP : Horizontal start point designation ---adjustable
3. CSVP : Vertical start point designation ---adjustable
4. CEHP : Horizontal END point designation ---adjustable
5. CEVP : Vertical END point designation ---adjustable.

6. Mode : uniformity mode select --- adjustable if need
*** 0 : 221point & 3level ---- default value
*** 1 : 221point & 4level
*** 2 : 825point & 3level
*** 3 : 825point & 4level
7. KHH : Upper 2byte of horizontal line correction coefficient - - Change according to CSHP, CEHP value.
8. KHL : Upper 2byte of vertical line correction coefficient -- Change according to CSHP, CEHP value.
** How to calculate KHH, KHL value
LCD panel size = 1280 x 720
Correction Point = 221 point
> 17 horizontal points x 13 vertical points
(16 horizontal segments x 12 vertical poins)
 H Coefficient(KHH, KHL)
> Calculation method (CEHP-CSHP=1280, Horizontal segment value =16)

How to Program a COX, Vizio and Sony Remote Control.

COX remote control programming procedure

Cox Universal Remote Control is already programmed to operate your cable converter, an RCA TV, an RCA VCR and a Pioneer audio receiver. To control devices other than the default brands, perform the following steps to reprogram your remote…

1. Turn on a device.

2. On the remote control, press a device key once (e.g., AUX, VCR, or CABLE). Press and hold SETUP until the selected mode key flashes twice, then release SETUP.

3. ENTER the four digit code for your device found in the sidebar to the right. If performed correctly, the selected mode key will blink twice. If the selected mode key emits a long blink, the code is invalid. Repeat steps 2 through 3 and try entering the same code again.

4. Aim the remote control at the device and press POWER once. The device should turn off. If it does not, repeat steps 2-3, trying each code for your brand until you find one that works. If it still does not work, try searching for the code.

Repeat steps 1-4 for each device you want the remote control to control. For future reference, write down each working device code.

How to program a Sony remote control

4 Digit Universal Remote Control Codes For Sony TVs.

Turn on the component to be programmed by your remote.

Press the SET button on the remote control.

Press the component button for the component being programmed.

Using the number keys enter the component’s 2,3,4, or 5 digit code.

Press the ENT button.

Point the remote control at the component.

Press the POWER button to verify operation.

Sony universal codes are: 0128, 0013, 0002, 0071, 0380.

If this does not work then repeat the procedure.

Enter one code at a time until you find one that functions.

How to program a Vizio remote to control another component

1  Turn on your TV (or device you want to control)

2  Press the TV (or device) button and hold for 5 seconds until the LED flashes twice. LED will remain lit.

3  Find the code for your TV or device in the code list BELOW and enter it using the Number Buttons.

(The LED flashes once after entering each digit. If the code is accepted, the LED flashes twice after the last digit is and then turns off)

4  Point the VIZIO remote control at the device and press the POWER button. If the device powers off, setup is complete. If not, repeat steps with a different code

How to Program DISH NETWORK, DIRECT TV Remote Control.

How to Program a DISH NETWORK Remote Control.

While at the device location, point your remote at the device. Press and hold the device mode button on your remote. All four mode buttons should light up.

Press the receiver POWER button on your DISH remote. The device button should light up.

Press the UP or DOWN arrow on the remote (about one press per second). During the scan, the mode light will remain lit when you are not pressing the up or down arrow, but will go out each time the arrow is pressed. Stop as soon as the device turns off, and proceed to step #5. This process may take several minutes. The TV should turn off.

If the scan has cycled through all available codes, the mode light will blink rapidly for two seconds, and will light up only when you press the up or down arrow. This may take approximately 5 minutes. If the scan fails to produce a code that will control the device, advise the customer that Dish does not currently support the equipment.

Press the POUND (#) button. The device Mode button should flash 3 times.

Press the POWER button on your remote to turn the device on. If this does not work, return to step 1. The device should turn on and respond to remote commands.

How to Program a DIRECTV Remote Control.

You can program your DIRECTV Universal Remote to control the following: TV, Audio components, Blu-ray player, DVD player, and VCR.

If you have an HD DVR or HD receiver, follow these steps:

Press MENU on your remote.

Select Settings & Help.

Select Settings.

Select Remote Control.

Select Program Remote, and then select the device you wish to program.

Follow the on-screen prompts to complete programming your remote.

Note: If your remote is not listed, or you need additional codes, use the code lookup tool to the right to find the 5-digit code for your device.

If you have a standard DVR or an SD receiver, follow these steps:

Press MENU on your remote.

Select Parental Favs & Setup.

Select System Setup.

Select Remote or Remote Control.

Select Program Remote, then select the device you wish to program.

Follow the on-screen prompts to complete programming your remote.

Note: If your remote is not listed, or you need additional codes, use the code lookup tool to the right to find the 5-digit code for your device.

How to Program any GE and Philips and RCA Universal Remote Control.

How to program a GE remote control

* Remove the battery cover and batteries from the GE Universal Remote Control. Look for a sticker that says the model number of the remote control. Identify the version number, indicated by “V2,” “V3” or “V4.” If no V-number is listed, then just assume it is version 1.

* Turn on the device you are programming in to the GE Universal Remote.

* Press down the “Setup” button for 5 seconds until the red indicator light turns on.

* Press the device button, such as “TV,” “DVD,” or “AUX.”

* Enter the 3 or 4 digit code. Once you enter a valid code the light turns off.

* Press the “Power” button to test to see if it worked. If not keep repeating the steps until you find a code that works.

How to Program any Philips Universal Remote Control.

1. Turn on the device you wish to program to operate with the Philips Universal Remote Control.

2. Hold down the “Code Search” button on the remote control. Release the button after the red indicator light blinks.

3. Press the device button, such as “TV” “CLB” “VCR” or “SAT” This will make the indicator light blink off and then back on.

4. Keep pressing the “CHAN +” button until the device changes channels. When the TV changes channels again, stop.

5. Press the “Mute” button to save the code in memory.

How to Program any RCA Universal Remote Control.

Find codes for each device and brand. 

Press and “HOLD” CODE SEARCH.

Press and release the TV or VCR button you want to set up. When the selected device button blinks go to the next step.

Next enter the 3 digit code from the TV, VCR or Cable Box remote code list.

Release CODE SEARCH.

With the device on press VOLUME UP to see if the tv responds.

If the TV or other does not respond then simply repeat steps 1-5 using another code number 

How to do convergence adjustments to a projection television

CONVERGENCE ADJUSTMENT 
Notes: In the convergence mode, if the first two displayed characters are "P", it means PAL, and if "Q", it means NTSC. In the two modes of DVD, the character display is the same as the two above-mentioned modes. "V" stands for VGA mode. These characters are omitted in the following OSD display description.

CONVERGENCE ADJUSTMENT IN PAL

With receiving of PAL signal, and the volume to 0, press and hold MUTE button until the red "MUTE" character becomes three colors (or white), then press MENU button on front panel of TV to enter "S" mode (Press "S" button on the jig to enter "S" mode directly when in production). Press yellow RECALL button to enter the phase of convergence adjustment, and the red convergence crosshatch displays in the screen. Press DISPLAY button to switch into green crosshatch signal.

Note" Generally speaking, you can go to Step IV, V, VI and VII directly.

Press TEXT button to clear fine/coarse adjusted data of the six channels in the RAM of convergence IC.

Note: Normally speaking, do not reset the RPTV to0. If it is necessary, exit convergence mode and time it before your resetting.

Adjustment of static convergence in green. Press PIP button until the video image super-imposes crosshatch-testing signal. Press PICTURE MODE SELECTION button until character "DCGH" appears, then press POSITION UP/DOWN buttons to call up "DCGH"( DCGV). Press VOLUME UP/DOWN buttons to make the center of green line (field) of 5-CH video test pattern locate at the center of the screen. Then press PIP button to conceal the video image.

Phase adjustment 

Adjustment of H. fine adjustment and phase of horizontal test 

Instate of crosshatch in green, press PICTURE MODE SELECTION button to call up " FINE NODE", and press SWAP button to switch the cursor into green. Press MUTE button until "P LOCK" appears. Now press POSITION UP button to display the GV value of fine adjusted convergence at H#4/V#4 point as the  maximum value on the screen. 

Press AV button to call up "FINE PHASE", Press VOLUME UP/DOWN buttons to make the peak appear at the vertical line at the right of horizontal center. 

Press AV button to call up "TEST PHASE". Adjust VOLUME UP/DOWN button to make the cursor locate at the peak. 

Reset GV value.

Setting of start lines of fine-adjusted convergence (setting of STARTLINES) 

In the state of crosshatch in green, press PICTURE MODE SELECTION button to enter "FINE MODE", then press VOLUME UP/DOWN buttons to set the GH fine adjustment value at H#4/V#4 as maximum, and make the peak displays on the screen. 

Press AV button to call up "STARTLINES", then press VOLUME UP/DOWN buttons till the peak displays at the center of the field. (Note: "START LINES" value can only be odd number). 

Return the GH fine adjusted value.

 Press PICTURE MODE SELECTION button to display "DCRH". Press POSITION UP/ DOWN buttons to call up "KGV3", and press VOLUME DOWN button to set KGV3 as a larger data. If the cursor is off the horizontal center, press AV button to call up "COAR PHASE", then press VOLUME UP/DOWN buttons to return the cursor to the original position.

Press PICTURE MODE SELECTION button until "DCRH" displays on the screen. Press POSITION UP/DOWN buttons to call up "KGH3", and adjust VOLUME UP/DOWN but-tons to set "KGH3" as a larger data. If the cursor is off the field center, press AV button to call up "START VALUE", then press VOLUME UP/DOWN buttons to return the cursor to the original position.

"COUNTUP" Setting

Press and hold AV button till "COUNTUP" appears, and press VOLUME UP/DOWN buttons to make crosshatch signal basically be straight in the V/H

direction. (The recommended COUNTUP data: PAL 3D, and NTSC 3D.

Coarse-adjustment of convergence in green

Press PICTURE MODE SELECTION button till "DCRH" appears, then press POSITION UP/DOWN buttons to select coarse adjustment order as follows:

Trim horizontal skew in green (KGH3).

Trim green horizontal pincushion distortion (KGH1)

Trim green horizontal amplitude (KGH2).

Trim green field pincushion distortion (KGV2).

Trim field keystone distortion (KGV1).

Trim green field skew (KGV3).

Fine-adjustment of convergence in green

Press PICTURE MODE SELECTION button to call up "FINE MODE", press SWAP but line to turn the cursor into green. Press DIGIT SELECTION button to select the point or line adjustment. Press MUTE button to move or fix the cursor: (When OSD is "POINT MOVE" or "LINE MOVE", press VOLUME UP/DOWN or POSITION.UP/DOWN buttons to move the cursor up, down, left and right. When OSD is "POINT LOCK" or "LINE LOCK", press VOLUME UP/DOWN or POSITION UP/DOWN buttons to adjust the dot or line data).

Notes:

•  In the process of fine adjustment, the cursor will change into 3 colors automatically. Press MUTE button after adjusting a data, the cursor will return to original color.

•  It is recommended to perform trimming fine errors from the center of the screen toward out-side area in circumference inaccordance with such an order as whirlpool-shape. In other word, at first, trim fine error at the point of H#4/V#4 of the screen center, next trim each fine point in circumference around outside of the 8 points, then trim other points in the same way.

•  If adjusting one point to increase fine error of nearby ones, which are not adjusted, you should adjust the data at your target point to make the error of nearby ones in the permissible range. Otherwise the fine adjustment data of nearby point might not meet the requirement even if the data reaches maximum.

•  You can save the adjusted data by pressing MENU button. When OSD displays "DATA OK", the data is saving, and when " DATA OK" disappears, it indicates the saving is complete.

•  When adjusting the parameters of coarse and fine adjustment in green, it will activate the convergence of the other two guns at the same time.

Adjustment of convergence in red

In convergence mode, press DISPLAY button to switch crosshatch state into red and green.

Adjustment of static convergence in red, adjust "DCRH" and "DCRV" of coarse adjustment convergence, so that superimpose the center of line-field in red with center of line-field in green.

Trim horizontal skew in red (KRH2)

Trim horizontal linearity distortion in red (KRH1)

Trim horizontal amplitude in red (KRH3)

Trim field keystone in red (KRV1)

Trim field skew in red (KRV2)

Adjusting procedures of fine adjustment data in red is the same as that in green, but crosshatch on the screen is yellow.

Adjustment of convergence in blue

In convergence state, press DISPLAY button so that crosshatches in red and blue appear on the screen, and press PIP button to make the cursor become blue.

Adjustment of static convergence in blue. Press and hold PICTURE NODE SELECTION button until "DCBH" appears, Press POSITION UP/DOWN buttons to call up "DCBH" and "DCBV", and press VOLUME UP/ DOWN buttons to position the line-field center of convergence in blue at the center of screen.

Trim horizontal skew in blue (KBH2),

Trim horizontal linearity distortion in blue (KBH1).

Trim horizontal amplitude in blue (KBH3).

Trim field keystone in blue (KBVI).

Trim field skew in blue (KBV2).

Saving 

Press MENU button to save the adjusted data. 

Press STILL/MOVABLE PICTURE ADJUSTMENT button to copy the adjusted data to the corresponding mode of DVD. 

CONVERGENCE ADJUSTMENT IN OTHER MODES 

Repeat the above-mentioned procedures for NTSC and VGA. 

CONVERGENCE ADJUSTMENT IN DVD MODE 

In DVD mode, it requires fine trimming PAL and NTSC.

How to Register Samsung TV

Registering your Samsung TV with its manufacturer has a number of benefits. From a safety perspective, it is important because it makes it easy for Samsung to let you know if there are any recalls on the set. Registration protects your warranty, as you have to enter the information from your sales receipt, providing a backup if your receipt is lost. It also gives you access to information and ongoing support and contact from Samsung to make it easier for you to enjoy your TV set.
Instructions
Copy down your Samsung TV's serial and model numbers. They are typically located on a large label on the back of your TV set and on a smaller label on the right side of your set. The smaller label has larger text and should still be readable if you have mounted your TV to the wall.
Visit the samsung.com website and click on the "Product Registration" link in the upper right corner.
Fill in all of the fields on the right side of the screen and click the "Submit" button. This screen asks you for basic information such as your name, email address, and zip code and also allows you to choose a password.
Wait a few moments for the "My Samsung" screen to appear and to switch over to the "My Account" tab.
Fill in the pull-down tabs labeled "Product Information" by choosing the correct option from the displayed choices. Enter your TV's serial number by typing it into the box labeled "Serial number."
Continue down the screen, filling in every field that is marked with a red asterisk. You may, if you choose, omit the other fields. When you are done, click the "Submit" button.
Check, or uncheck, any of the boxes in the section labeled "Preferences" in the following screen to determine what information, if any, Samsung will send you. You may also fill in the optional "Additional Information" section below that if you choose. Click the "Submit" button when you are done with this screen.
Click the "OK" button in the small alert box reading "Account updated successfully" that pops up. At that point, you have finished the registration process.