HP Pavilion
dm1 - HP Mini 311: DISASSEMBLING
PROCEDURE
How
to remove Battery
Before
removing the battery, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then unplugging the AC adapter from the computer.
Remove the battery:
1. Turn the computer upside down on a flat surface, with the battery bay toward you.
2. Slide the battery release latches 1 to release the battery.
3. Remove the battery 2.
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then unplugging the AC adapter from the computer.
Remove the battery:
1. Turn the computer upside down on a flat surface, with the battery bay toward you.
2. Slide the battery release latches 1 to release the battery.
3. Remove the battery 2.
How
to remove WLAN module
Before
removing the WLAN module, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then unplugging the AC adapter from the computer.
4. Remove the battery
Remove the WLAN module:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then unplugging the AC adapter from the computer.
4. Remove the battery
Remove the WLAN module:
1.
Position the computer with the front toward you.
2. Loosen the 2 Phillips PM2.0×6.0 captive screws 1 that secure the accessory compartment cover to the computer.
3. Lift the left side of the cover 2 to detach it from the computer, and remove the accessory compartment cover.
2. Loosen the 2 Phillips PM2.0×6.0 captive screws 1 that secure the accessory compartment cover to the computer.
3. Lift the left side of the cover 2 to detach it from the computer, and remove the accessory compartment cover.
The
accessory compartment cover is available using spare part number 580056-001.
4.
Disconnect the WLAN antenna cables 1 from the terminals on the WLAN module. The
black WLAN antenna cable is connected to the WLAN module “Main” terminal. The
white WLAN antenna cable is connected to the WLAN module “Aux” terminal.
5.
Remove the Phillips PM2.0×4.0 screw 2 that secures the WLAN module to the
system board. (The WLAN module tilts up.)
6. Remove the WLAN module 3 by pulling it away from the slot at an angle.
WLAN modules are designed with a notch 4 to prevent incorrect insertion of the WLAN module into the WLAN module slot.
6. Remove the WLAN module 3 by pulling it away from the slot at an angle.
WLAN modules are designed with a notch 4 to prevent incorrect insertion of the WLAN module into the WLAN module slot.
How
to remove WWAN module
Before
removing the WWAN module, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then unplugging the AC adapter from the computer.
4. Remove the battery
5. Remove the accessory compartment cover
Remove the WWAN module:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then unplugging the AC adapter from the computer.
4. Remove the battery
5. Remove the accessory compartment cover
Remove the WWAN module:
1.
Position the computer with the front toward you.
2. Disconnect the WWAN antenna cables 1 from the terminals on the WWAN module.
The red WWAN antenna cable is connected to the WWAN module “Main” terminal. The blue WWAN antenna cable is connected to the WWAN module “Aux” terminal.
3. Remove the 2 Phillips PM2.0×4.0 screws 2 that secure the WWAN module to the system board. (The WWAN module tilts up.)
4. Remove the WWAN module 3 by pulling it away from the slot at an angle. WWAN modules are designed with a notch 4 to prevent incorrect insertion of the WWAN module into the WWAN module slot.
2. Disconnect the WWAN antenna cables 1 from the terminals on the WWAN module.
The red WWAN antenna cable is connected to the WWAN module “Main” terminal. The blue WWAN antenna cable is connected to the WWAN module “Aux” terminal.
3. Remove the 2 Phillips PM2.0×4.0 screws 2 that secure the WWAN module to the system board. (The WWAN module tilts up.)
4. Remove the WWAN module 3 by pulling it away from the slot at an angle. WWAN modules are designed with a notch 4 to prevent incorrect insertion of the WWAN module into the WWAN module slot.
How
to remove RTC battery
Before
removing the RTC battery, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then unplugging the AC adapter from the computer.
4. Remove the battery
5. Remove the accessory compartment cover
Remove the RTC battery:
1. Position the computer with the front toward you.
2. Disconnect the RTC battery cable 1 from the system board.
3. Slide the RTC battery 2 directly back to remove it.
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then unplugging the AC adapter from the computer.
4. Remove the battery
5. Remove the accessory compartment cover
Remove the RTC battery:
1. Position the computer with the front toward you.
2. Disconnect the RTC battery cable 1 from the system board.
3. Slide the RTC battery 2 directly back to remove it.
How
to remove Hard drive
Before
removing the hard drive, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then unplugging the AC adapter from the computer.
4. Remove the battery
5. Remove the accessory compartment cover
Remove the hard drive:
1. Position the computer with the front toward you.
2. Disconnect the hard drive connector 1.
3. Grasp the Mylar tab 2 in the hard drive bay, and then lift it up at an angle.
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then unplugging the AC adapter from the computer.
4. Remove the battery
5. Remove the accessory compartment cover
Remove the hard drive:
1. Position the computer with the front toward you.
2. Disconnect the hard drive connector 1.
3. Grasp the Mylar tab 2 in the hard drive bay, and then lift it up at an angle.
4.
Remove the hard drive 3 from the hard drive bay.
How
to remove Keyboard
Before
removing the keyboard, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then unplugging the AC adapter from the computer.
4. Remove the battery
5. Remove the accessory compartment cover
6. Remove the hard drive
Remove the keyboard:
1. Position the computer with the front toward you.
2. Remove the 4 Phillips PM2.0×7.0 screws that secure the keyboard to the computer.
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then unplugging the AC adapter from the computer.
4. Remove the battery
5. Remove the accessory compartment cover
6. Remove the hard drive
Remove the keyboard:
1. Position the computer with the front toward you.
2. Remove the 4 Phillips PM2.0×7.0 screws that secure the keyboard to the computer.
3.
Turn the computer display-side up, with the front toward you.
4.
Open the computer as far as possible.
5. Lift the rear edge 1 and then the left edge 2 of the keyboard until it rests at an angle.
6. Slide the keyboard 3 back until it rests on the display.
5. Lift the rear edge 1 and then the left edge 2 of the keyboard until it rests at an angle.
6. Slide the keyboard 3 back until it rests on the display.
7.
Release the zero insertion force (ZIF) connector 1 to which the keyboard cable
is attached, and then disconnect the keyboard cable 2 from the system board.
