Service Mode Setting
1. Set the “Status” to “On” in the “Setup” menu.
2. Close the menu by pressing “MENU” if its displayed.
3. Press the buttons in the following order in 5 seconds: ENTER > ENTER > LEFT ARROW > ENTER
4. The message “Do you wish to enter into the SERVICE MODE? Yes No” will be displayed.
5. Select “Yes”.
Model Name Display Mode Setting
1. If the menu is being displayed, press the [MENU] button to close the menu.
2. Press the buttons within 5 seconds in the following order:
ENTER > UP ARROW > DOWN ARROW > ENTER
Even if the message “Not applicable!” is displayed, ignore it. If the key operations failed, wait for at least 6 seconds since the last key is pressed, and perform the key operations again.
3. “Which mode do you wish to display? Model Name Display/Motionflow/Off” is displayed.
4. Select “Model Name Display”.
Motionflow Mode Setting
1. If the menu is being displayed, press the [MENU] button to close the menu.
2. Press the buttons within 5 seconds in the following order:
ENTER > UP ARROW > DOWN ARROW > ENTER
Even if the message “Not applicable!” is displayed, ignore it. If the key operations failed, wait for at least 6 seconds since the last key is pressed, and perform the key operations again.
3. “Which mode do you wish to display? Model Name Display/Motionflow/Off” is displayed.
4. Select “Motionflow”.
IRIS Copy
1. Enter the Service Mode.
2. Set OTHER: 01 Iris/Adj in the Device Menu to 1.
3. Change the value of OTHER: 02 Iris/Open Reg.
4. Change the value of OTHER: 03 Iris/Close Reg.
5. Return OTHER: 01 Iris/Adj in the Device Menu to 0.
6. Perform Save to Memory.
Panel Driver Gain B Copy
1. Enter the Service Mode.
2. Change the value of Panel Driver: 03 P. Drv/Gain B in Device Menu.
3. Perform Save to Memory
Lens Shift Data Copy
1. Enter the Service Mode.
2. Change the value of OTHER: 13 Lens Shift/H Center in Device Menu.
3. Change the value of OTHER: 14 Lens Shift/V Center in Device Menu.
4. Change the value of OTHER: 15 Lens Shift/V Top Limit in Device Menu.
5. Change the value of OTHER: 16 Lens Shift/V Bottom Limit in Device Menu.
6. Change the value of OTHER: 17 Lens Shift/Right Limit in Device Menu.
7. Change the value of OTHER: 18 Lens Shift/Left Limit in Device Menu.
8. Perform Save to Memory.
Panel Alignment Data Copy
1. Enter the Service Mode.
2. Change the value of Display Engine: 06 R REG H in Device Menu.
3. Change the value of Display Engine: 07 R REG V in Device Menu.
4. Change the value of Display Engine: 08 B REG H in Device Menu.
5. Change the value of Display Engine: 09 B REG V in Device Menu.
6. Perform Save to Memory.
1. Set the “Status” to “On” in the “Setup” menu.
2. Close the menu by pressing “MENU” if its displayed.
3. Press the buttons in the following order in 5 seconds: ENTER > ENTER > LEFT ARROW > ENTER
4. The message “Do you wish to enter into the SERVICE MODE? Yes No” will be displayed.
5. Select “Yes”.
Model Name Display Mode Setting
1. If the menu is being displayed, press the [MENU] button to close the menu.
2. Press the buttons within 5 seconds in the following order:
ENTER > UP ARROW > DOWN ARROW > ENTER
Even if the message “Not applicable!” is displayed, ignore it. If the key operations failed, wait for at least 6 seconds since the last key is pressed, and perform the key operations again.
3. “Which mode do you wish to display? Model Name Display/Motionflow/Off” is displayed.
4. Select “Model Name Display”.
Motionflow Mode Setting
1. If the menu is being displayed, press the [MENU] button to close the menu.
2. Press the buttons within 5 seconds in the following order:
ENTER > UP ARROW > DOWN ARROW > ENTER
Even if the message “Not applicable!” is displayed, ignore it. If the key operations failed, wait for at least 6 seconds since the last key is pressed, and perform the key operations again.
3. “Which mode do you wish to display? Model Name Display/Motionflow/Off” is displayed.
4. Select “Motionflow”.
IRIS Copy
1. Enter the Service Mode.
2. Set OTHER: 01 Iris/Adj in the Device Menu to 1.
3. Change the value of OTHER: 02 Iris/Open Reg.
4. Change the value of OTHER: 03 Iris/Close Reg.
5. Return OTHER: 01 Iris/Adj in the Device Menu to 0.
6. Perform Save to Memory.
Panel Driver Gain B Copy
1. Enter the Service Mode.
2. Change the value of Panel Driver: 03 P. Drv/Gain B in Device Menu.
3. Perform Save to Memory
Lens Shift Data Copy
1. Enter the Service Mode.
2. Change the value of OTHER: 13 Lens Shift/H Center in Device Menu.
3. Change the value of OTHER: 14 Lens Shift/V Center in Device Menu.
4. Change the value of OTHER: 15 Lens Shift/V Top Limit in Device Menu.
5. Change the value of OTHER: 16 Lens Shift/V Bottom Limit in Device Menu.
6. Change the value of OTHER: 17 Lens Shift/Right Limit in Device Menu.
7. Change the value of OTHER: 18 Lens Shift/Left Limit in Device Menu.
8. Perform Save to Memory.
Panel Alignment Data Copy
1. Enter the Service Mode.
2. Change the value of Display Engine: 06 R REG H in Device Menu.
3. Change the value of Display Engine: 07 R REG V in Device Menu.
4. Change the value of Display Engine: 08 B REG H in Device Menu.
5. Change the value of Display Engine: 09 B REG V in Device Menu.
6. Perform Save to Memory.
