Direct
Code setup
1.
Locate the Remote Code.
2. Manually turn on the device you wish to control.
3. Press and hold the SETUP button until the red indicator light stays on (approximately 2 seconds) and then release the SETUP button.
4. Press and release the desired device button on the remote (TV, CBL/SAT). The red indicator will blink once and then remain on.
5. Enter the first 4-digit code previously found in the code list using the number buttons on the remote. If the code entered is a valid code, the red indicator light will turn off. If the code entered is not a valid code, the red indicator light will flash and remain on allowing you to re-enter the code.
Note: If no buttons are pressed for 35 seconds, the remote will exit the SETUP mode and you will have to start over.
2. Manually turn on the device you wish to control.
3. Press and hold the SETUP button until the red indicator light stays on (approximately 2 seconds) and then release the SETUP button.
4. Press and release the desired device button on the remote (TV, CBL/SAT). The red indicator will blink once and then remain on.
5. Enter the first 4-digit code previously found in the code list using the number buttons on the remote. If the code entered is a valid code, the red indicator light will turn off. If the code entered is not a valid code, the red indicator light will flash and remain on allowing you to re-enter the code.
Note: If no buttons are pressed for 35 seconds, the remote will exit the SETUP mode and you will have to start over.
6.
Point the remote at the device. Press the POWER button - if the device turns
off, no further programming is required for that device. If the device does not
turn off, return to step 3 and use the next code found in the code list.
Continue this process until a code for your device is found.
Programming Notes
#
If your device does not respond to the remote after trying all codes listed or
your brand is not listed in the code list, use the Auto Code Search method to
program your remote.
# Sometimes the first code that “works” with your device may operate only a few functions of your device. There may be another code in the code list that performs more functions. Try other codes from the code list for more functionality.
# You can use any device button to control other devices in your home entertainment system. For example, you can use the CBL/SAT device button to control an audio receiver.
# Write down the code found to operate your device for future reference.
# Sometimes the first code that “works” with your device may operate only a few functions of your device. There may be another code in the code list that performs more functions. Try other codes from the code list for more functionality.
# You can use any device button to control other devices in your home entertainment system. For example, you can use the CBL/SAT device button to control an audio receiver.
# Write down the code found to operate your device for future reference.
Auto
Code Search
The
Auto Code Search searches automatically through all of the codes stored in this
remote. Read all the following steps prior to starting the auto search as you
will need to be prepared to lock in the proper code when found.
1. Manually turn on the device you wish to control.
2. Press and hold the SETUP button until the red indicator light stays on (approximately 4 seconds) and then release the button.
3. Press and release the desired device button on the remote (TV, CBL/SAT). The red indicator will blink once and then remain on.
4. Point the remote at the device and press and release the POWER button to start the search. The red indicator will flash (approximately every 2 seconds) as the remote searches.
NOTE: The remote must be pointed at the device for the duration of this search.
5. Place your finger on the #1 button so you are prepared to lock-in the code.
6. When the device shuts off or begins playing, press the #1 button to lock-in the code. The red indicator light will turn off. NOTE: You have approximately two seconds after the device shuts off or begins playing to lock in the code.
7. Point the remote at the device and check to see if the remote operates the device as desired. If it does, no further programming is required for that device. If it does not, return to step 2 and start the auto search.
1. Manually turn on the device you wish to control.
2. Press and hold the SETUP button until the red indicator light stays on (approximately 4 seconds) and then release the button.
3. Press and release the desired device button on the remote (TV, CBL/SAT). The red indicator will blink once and then remain on.
4. Point the remote at the device and press and release the POWER button to start the search. The red indicator will flash (approximately every 2 seconds) as the remote searches.
NOTE: The remote must be pointed at the device for the duration of this search.
5. Place your finger on the #1 button so you are prepared to lock-in the code.
6. When the device shuts off or begins playing, press the #1 button to lock-in the code. The red indicator light will turn off. NOTE: You have approximately two seconds after the device shuts off or begins playing to lock in the code.
7. Point the remote at the device and check to see if the remote operates the device as desired. If it does, no further programming is required for that device. If it does not, return to step 2 and start the auto search.
Programming
Notes
#
This process may take several minutes as the remote contains many codes.
# The SETUP button can be used during the search process to reverse the direction of the search of the remote codes. For example, if you miss the code for your device and the remote is continuing to search (as indicated by the blinking red light), press the SETUP button and the code search will reverse direction and return to the code.
# When using the Auto Code Search programming method, the device button corresponding to the type of device you want to control must be selected (for example, the TV device button must be selected in step 3 if you want to control a TV.
# Sometimes the first code that “works” with your device may operate only a few functions of your device. There may be another code in the code list that performs more functions. Continue the code search as directed above until the best code is found.
# The SETUP button can be used during the search process to reverse the direction of the search of the remote codes. For example, if you miss the code for your device and the remote is continuing to search (as indicated by the blinking red light), press the SETUP button and the code search will reverse direction and return to the code.
# When using the Auto Code Search programming method, the device button corresponding to the type of device you want to control must be selected (for example, the TV device button must be selected in step 3 if you want to control a TV.
# Sometimes the first code that “works” with your device may operate only a few functions of your device. There may be another code in the code list that performs more functions. Continue the code search as directed above until the best code is found.
STREAMING MEDIA
Apple 5541, 4295
Asus 1684
Dlink 1614, 1724
HP 1624
Iomega 1744
LG 1714
Magnavox 1704
Netgear 1604, 4475
Niveus 1634
Philips 1654
Popcorn Hour 1664
RCA 1694
Roku 4395, 4355
Seagate 1674
Sling Media 1644
Vudu 1734
WD 4345, 4265
X-Box 4245, 4255
