TEST MODE
Setting method:
1. In the state of source off (the clock is displayed on the liquid crystal display), enter the test mode by pressing the buttons on the remote commander in order of the [4] > [5] > [1] (press only the [1] button for two seconds).
2. It is set to the test mode, and all segments of the liquid crystal display light.
Releasing method:
Press the [SOURCE OFF] button for 1 second.
MICROPHONE AUDIO LOOPBACK
To confirm the state of the internal microphone used when a handsfree function is used, the microphone audio is output from the speaker.
Procedure:
1. Enter the test mode.
2. Press the [SOURCE OFF] button to select the Bluetooth Phone function.
3. On/off of the microphone audio loopback function changes whenever the [ALBUM UP 2] button is pressed (“ALBM” is displayed in the liquid crystal display)
1. In the state of source off (the clock is displayed on the liquid crystal display), enter the test mode by pressing the buttons on the remote commander in order of the [4] > [5] > [1] (press only the [1] button for two seconds).
2. It is set to the test mode, and all segments of the liquid crystal display light.
Releasing method:
Press the [SOURCE OFF] button for 1 second.
MICROPHONE AUDIO LOOPBACK
To confirm the state of the internal microphone used when a handsfree function is used, the microphone audio is output from the speaker.
Procedure:
1. Enter the test mode.
2. Press the [SOURCE OFF] button to select the Bluetooth Phone function.
3. On/off of the microphone audio loopback function changes whenever the [ALBUM UP 2] button is pressed (“ALBM” is displayed in the liquid crystal display)
BLUETOOTH FUNCTION CHECKING METHOD USING A CELLULAR PHONE
1. Required Equipment
Set to be tested (DSX-M50BT)
Cellular phone
Bluetooth audio devices
Speaker connection
DC power supply (12 V)
2. Preparation
Confirm the setting of the DSX-M50BT, and note down it.
Press the [CALL] button and rotate the control dial until “PAIRING” appears, then press it, confirm that the Bluetooth signal icon is flashing.
Turn on the Bluetooth function of the cellular phone.
3. Test Environment
No other Bluetooth device is making a communication in the periphery (within 20 m).
No other DSX-M50BT are supplied with electric power.
There are no two or more wireless LAN access points in the periphery (with 50 m) (one is OK).
The set should be tested in a place such as a meeting room, free from ambient noise.
The speaker at the far end should be in a place such as another meeting room separated acoustically.
1. Required Equipment
Set to be tested (DSX-M50BT)
Cellular phone
Bluetooth audio devices
Speaker connection
DC power supply (12 V)
2. Preparation
Confirm the setting of the DSX-M50BT, and note down it.
Press the [CALL] button and rotate the control dial until “PAIRING” appears, then press it, confirm that the Bluetooth signal icon is flashing.
Turn on the Bluetooth function of the cellular phone.
3. Test Environment
No other Bluetooth device is making a communication in the periphery (within 20 m).
No other DSX-M50BT are supplied with electric power.
There are no two or more wireless LAN access points in the periphery (with 50 m) (one is OK).
The set should be tested in a place such as a meeting room, free from ambient noise.
The speaker at the far end should be in a place such as another meeting room separated acoustically.
Precautions
Beware of the following points when conducting the talking test:
# There is no fault if a talking can be made by adjusting appropriately the volume of the telephone of the other party and the cellular phone connected through the Bluetooth, besides the setup of DSX-M50BT.
# The speaker’s voice will become loud naturally if the periphery is noisy, or become low if quiet (even though the speaker intents to talk on the same volume level).
# The speaker’s voice will become loud naturally if the other party’s voice is loud.
Beware of the following points when conducting the talking test:
# There is no fault if a talking can be made by adjusting appropriately the volume of the telephone of the other party and the cellular phone connected through the Bluetooth, besides the setup of DSX-M50BT.
# The speaker’s voice will become loud naturally if the periphery is noisy, or become low if quiet (even though the speaker intents to talk on the same volume level).
# The speaker’s voice will become loud naturally if the other party’s voice is loud.
Bluetooth Phone (Hands Free) Function Check
1. Search for this unit from the Bluetooth device (cellular phone), and confirm whether this unit (“Sony Automotive”) is displayed.
2. Search for the distance of this unit and the Bluetooth device (cellular phone) about 5 m apart.
Confirm whether the Bluetooth device (or this unit) is displayed after it searches.
3. Do the pairing of the cellular phone and this unit (input of pass key).
4. Connect the cellular phone with this unit, and confirm the “HF” icon lights.
5. Confirm the connection continues even if the distance of the cellular phone and this unit is separated by about 5 m.
6. Set this unit besides the “BT PHONE” source, and call the cellular phone connected with this unit.
Confirm the automatic change of this unit into “BT PHONE” source, and the change into the screen for incoming calls.
Confirm the ring tone is heard from the speaker.
7. Take a phone call (press the [CALL] button), and start a conversation.
Confirm the other person voice is heard from the front speaker.
Speak toward the microphone of this unit, and confirm whether the other party hears its voice.
Compare the sound quality with a normal set. Confirm that there is no big difference.
8. Turn on ACC from off, and confirm whether this unit connects Bluetooth with the cellular phone again.
Note: Depending on the cellular phone, it might not reconnect automatically when ACC is turned on.
1. Search for this unit from the Bluetooth device (cellular phone), and confirm whether this unit (“Sony Automotive”) is displayed.
2. Search for the distance of this unit and the Bluetooth device (cellular phone) about 5 m apart.
Confirm whether the Bluetooth device (or this unit) is displayed after it searches.
3. Do the pairing of the cellular phone and this unit (input of pass key).
4. Connect the cellular phone with this unit, and confirm the “HF” icon lights.
5. Confirm the connection continues even if the distance of the cellular phone and this unit is separated by about 5 m.
6. Set this unit besides the “BT PHONE” source, and call the cellular phone connected with this unit.
Confirm the automatic change of this unit into “BT PHONE” source, and the change into the screen for incoming calls.
Confirm the ring tone is heard from the speaker.
7. Take a phone call (press the [CALL] button), and start a conversation.
Confirm the other person voice is heard from the front speaker.
Speak toward the microphone of this unit, and confirm whether the other party hears its voice.
Compare the sound quality with a normal set. Confirm that there is no big difference.
8. Turn on ACC from off, and confirm whether this unit connects Bluetooth with the cellular phone again.
Note: Depending on the cellular phone, it might not reconnect automatically when ACC is turned on.
Bluetooth Audio Function Check
Note: Depending on the connecting BT Audio device, track information (e.g. track name, playback time) can be on display.
If the device doesn’t support AVRCP1.3, or, if AVRCP1.3 feature of the device has not been validated with DSX-M50BT; the track information won’t be shown.
Even if there is no track information on display during playback of an AVRCP1.3 device, it is not a failure of DSX-M50BT.
1. Connect the Bluetooth audio device (or cellular phone with Bluetooth audio function) with this unit, and confirm the “Audio Streaming” icon lights.
2. Playback Bluetooth audio. Confirm the sound is emitted from this unit when this unit is switched to “Bluetooth Audio” source.
3. Confirm whether Bluetooth audio can be controlled by operating this unit (the [SEEK+ ], [SEEK– ] and [PAUSE ] buttons operation).
Note: Varies depending on the connected Bluetooth audio device.
Note: Depending on the connecting BT Audio device, track information (e.g. track name, playback time) can be on display.
If the device doesn’t support AVRCP1.3, or, if AVRCP1.3 feature of the device has not been validated with DSX-M50BT; the track information won’t be shown.
Even if there is no track information on display during playback of an AVRCP1.3 device, it is not a failure of DSX-M50BT.
1. Connect the Bluetooth audio device (or cellular phone with Bluetooth audio function) with this unit, and confirm the “Audio Streaming” icon lights.
2. Playback Bluetooth audio. Confirm the sound is emitted from this unit when this unit is switched to “Bluetooth Audio” source.
3. Confirm whether Bluetooth audio can be controlled by operating this unit (the [SEEK+ ], [SEEK– ] and [PAUSE ] buttons operation).
Note: Varies depending on the connected Bluetooth audio device.
INITIALIZING BLUETOOTH
Procedure:
1. In the state of source off (the clock is displayed), press and hold the [PUSH ENTER/SELECT] button.
2. Rotate the control dial, and select the “BT INIT”.
3. Press the [PUSH ENTER/SELECT] button, and the message “INIT-NO” is displayed on the liquid crystal display.
4. Rotate the control dial clockwise, and the message “INITYES” is displayed on the liquid crystal display.
5. Press the [PUSH ENTER/SELECT] button, and the message “INITIAL” is blinked on the liquid crystal display.
6. When “Bluetooth Initialize” is completed, the message “COMPLETE” is displayed on the liquid crystal display for a moment.
7. Press the [ RUTURN /MODE] button, and return to the state of source off (the clock is displayed) mode.
1. In the state of source off (the clock is displayed), press and hold the [PUSH ENTER/SELECT] button.
2. Rotate the control dial, and select the “BT INIT”.
3. Press the [PUSH ENTER/SELECT] button, and the message “INIT-NO” is displayed on the liquid crystal display.
4. Rotate the control dial clockwise, and the message “INITYES” is displayed on the liquid crystal display.
5. Press the [PUSH ENTER/SELECT] button, and the message “INITIAL” is blinked on the liquid crystal display.
6. When “Bluetooth Initialize” is completed, the message “COMPLETE” is displayed on the liquid crystal display for a moment.
7. Press the [ RUTURN /MODE] button, and return to the state of source off (the clock is displayed) mode.
