Entering
Service Mode
In power on condition, no discs and tray close, it will be entered into service mode by the following operation using the remote controller. However, it will not be entered when Media Select Item is SD Memory.
Service Mode using remote controller
Press the following buttons on the remote controller in power on condition, no discs and tray close;
[2] > [5] > [8] > [0] > [CLEAR]
In power on condition, no discs and tray close, it will be entered into service mode by the following operation using the remote controller. However, it will not be entered when Media Select Item is SD Memory.
Service Mode using remote controller
Press the following buttons on the remote controller in power on condition, no discs and tray close;
[2] > [5] > [8] > [0] > [CLEAR]
Release
from Service Mode
Press the [POWER OFF] button to turn off power.
Press the [POWER OFF] button to turn off power.
HOW
TO INITIALIZE THE BLU-RAY DISC PLAYER
To put the program back at the factory-default, initialize the BD player as the following procedure.
1. Turn the power on.
2. Remove the disc on the tray and close the tray.
3. Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order.
4. Press [ STOP ] button on the remote control unit.
5. To exit this mode, press [POWER OFF] button.
To put the program back at the factory-default, initialize the BD player as the following procedure.
1. Turn the power on.
2. Remove the disc on the tray and close the tray.
3. Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order.
4. Press [ STOP ] button on the remote control unit.
5. To exit this mode, press [POWER OFF] button.
FIRMWARE
UPDATE PROCEDURE
1. Turn the power on and remove the disc on the tray and close the tray.
2. To put the BD player into version up mode, press [9], [8], [7], [6], and [POP UP MENU/MENU] buttons on the remote control unit in that order.
The tray will open automatically.
1. Turn the power on and remove the disc on the tray and close the tray.
2. To put the BD player into version up mode, press [9], [8], [7], [6], and [POP UP MENU/MENU] buttons on the remote control unit in that order.
The tray will open automatically.
3.
Load the disc with new version.
4. The BD player enters the F/W version up mode automatically.
4. The BD player enters the F/W version up mode automatically.
5.
After Update,checksum on the VFD will displayed.
6.
Unplug the AC cord from the AC outlet. Then plug it again.
7. Turn the power on.
8. Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order.
7. Turn the power on.
8. Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order.
9.
Press [ STOP ] button on the remote control unit and verify the firmware
version
10.
To exit this mode, press [POWER OFF] button.
How
to Verify the Firmware Version
1. Turn the power on.
2. Remove the disc on the tray and close the tray.
3. Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order.
1. Turn the power on.
2. Remove the disc on the tray and close the tray.
3. Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order.
4.
Press [ STOP ] button on the remote control unit and verify the firmware
version
5.
To exit this mode, press [POWER OFF] button.
TRAY
LOCK MODE
Enter
this mode using the following procedure.
1. Confirm that the TV Monitor is connected.
2. With playback stopped, press [SETUP], [TOP MENU], [3], [AUDIO], [0] and [SETUP] buttons on the remote control unit in that order. "Trade-On" appears in the upper right corner on the screen.
3.
To exit this mode, press [SETUP], [TOP MENU], [3], [AUDIO], [0] and [SETUP]
buttons on the remote control unit in that order. "Trade-Off" appears
in the upper right corner on the screen.1. Confirm that the TV Monitor is connected.
2. With playback stopped, press [SETUP], [TOP MENU], [3], [AUDIO], [0] and [SETUP] buttons on the remote control unit in that order. "Trade-On" appears in the upper right corner on the screen.
