GE Home appliances Error codes cause and solution - GE Dishwasher Error codes

GE Home appliances Error codes cause and solution - GE Dishwasher Error codes  - GE Microwave Error codes - GE  Cooking Range -Stove Error codes - GE Washing Machine Error codes

GE Error codes

Dishwasher  Error codes Causes and Solution

PF

Causes

Power Failure

Solution

Select 'cancel' to clear code. If error persists, check electrical connections to dishwasher and electronic control (control board). Replace if defective.

C1

Causes

Partially Blocked Drain

Solution

This error will occur when dishwasher was unable to pump out water in less than 95 seconds. Check drain line for debris and blockage. If clear, check for a restricted drain valve in the pump.

C2

Causes

Drain Line Totally Blocked

Solution

This error will occur when dishwasher is unable to pump out water within the maximum time of 405 seconds. Check drain line and drain valve in pump for debris and blockage. Note: If a new garbage disposal has been installed, remove knock out plug for dishwasher drain.

C3

Causes

Will Not Drain

Solution

This occurs when dishwasher is not able to switch to the drain mode. 

C4

Causes

Water Over-Fill Fault

Solution

This error usually indicates bad water inlet valve. Check for high water pressure to unit.

C5

Causes

Low Water Fill

Solution

This error usually indicates bad water inlet valve. Check for low water pressure to unit.

C6

Causes

Water Temperature Too Low (After 20 Minute Extension)

Solution

Check heating element and thermostat for continuity.

C7

Causes

Temperature Sensor Bad

Solution

Replace temperature sensor (remove door to access panel, sensor should be located inside the door).

C8

Causes

Detergent Cup Blocked

Solution

Check for debris around detergent cup. Keep objects clear of cup when loading dishwasher.

Microwave Error codes Causes and Solution

F1

Causes

Oven Cavity Thermistor Open

Solution

Check oven thermistor for continuity and replace if zero or infinite ohms.

F2

Causes

Oven Cavity Thermistor Closed

Solution

Check oven thermistor for continuity and replace if zero or infinite ohms.

F3

Causes

Touch Pad Shorted

Solution

Replace touch pad (key panel).

F4 / F5

Causes

Humidity Sensor Open of Shorted

Solution

Replace humidity sensor.

F6

Causes

Shorted Temperature Probe

Solution

Replace temperature probe.

Cooking Range -Stove Error codes Causes and Solution

F0

Causes

Function Key Stuck

Solution

Replace touch pad or touch pad and control board if one assembly. Refer to F1 Test for more information.

F1

Causes

Function Key Stuck

Solution

Replace touch pad or touch pad and control board if one assembly. Refer to F1 Test for more information.

F2 (During Bake)

Causes

Oven Control Senses Oven Temperature above 615F-630F

Solution

If temperature has exceeded 615F-630F, check for welded contacts on bake and broil relays. If present, replace control board. If temperature has NOT exceeded 615F-630F, check sensor, sensor harness, and the sensor harness connection at sensor and oven control. If found defective, replace sensor. Also check for any causes of high resistance in the oven temperature sensor circuit.

F2 (During Clean)

Causes

Oven Control Senses Oven Temperature Above 915F-930F

Solution

If temperature has exceeded 915F-930F, check for welded contacts on the bake and broil relays. If present, replace control board. If temperature has NOT exceeded 915F-930F, check sensor, sensor harness, and the sensor harness connection at sensor and oven control. If found defective, replace sensor. Also check for any causes of high resistance in the oven temperature sensor circuit.

F3 / F4

Causes

Open or Shorted Oven Temperature Sensor (RTD)

Solution

Check sensor harness and connection between oven sensor and oven control. If wiring is ok, replace control board.

F5

Causes

Loss of Relay Drive Circuit

Solution

If error cannot be cancelled by selecting the 'cancel' function, the control board will need to be replaced.

F8

Causes

Shorted Meat Probe

Solution

This error indicates a problem with either the probe, receptacle, or probe circuit. Check the probe for pinched wires and make sure there is no condensation or contamination on receptacle.

F9

Causes

Door Lock Switch

Solution

Check door lock switches and wiring.

FC

Causes

Door Lock Circuit

Solution

Check wiring and test switches. Most common cause of this error is pinched wires between the control and the door lock switches on motorized lock circuits.

FD

Causes

Short Meat Probe
Solution

This error indicates a problem with either the probe, receptacle, or probe circuit. Check the probe for pinched wires and make sure there is no condensation or contamination on receptacle. If ok, replace probe.

FF

Causes

Loss of Door Motor Safety Switch

Solution

Replace control board.

FFF

Causes

EEPROM Checksum Error

Solution

Replace control board.

Washing Machine Error codes causes and solution

IE

Causes

Water Level Sensor Error

Solution

Press 'Power' button and check wiring harness, pressure sensor switch, and circuit board for defects. Replace faulty part.

7E

Causes

Water Supply Error

Solution

Press 'Power' button and check wiring harness, water valve, pressure sensor switch, and circuit board for defects. Replace faulty part.

E

Causes

Drain Pump Error

Solution

Press 'Power' button and check wiring harness, pump motor, and circuit board for defects. Replace faulty part.

dE

Causes

Lid Open Error

Solution

Close lid. If error persists, check wiring harness, lid switch, unbalance switch, and circuit board for defects. Replace faulty part.

UE

Causes

Unbalance Switch Error

Solution

Open lid and re-balance laundry manually. If error persists, check wiring harness, unbalance switch, and circuit board for defects. Replace faulty part.

OE

Causes

Water Overflow Error

Solution

Turn off water supply to washer and disconnect power and unplug unit. Check wiring harness, water inlet water valve, pressure sensor switch, and circuit board for defects. Replace if faulty.