Freemotion t6.0:
TROUBLESHOOTING
The
power does not turn on
a. Make sure that the power cord is plugged into a surge suppressor and that the surge suppressor is plugged into a properly grounded outlet. Use only a surge suppressor that meets all of the specifications.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the power switch located on the treadmill frame near the power cord. If the switch protrudes as shown, the switch has tripped. To reset the power switch, wait for five minutes and then press the switch back in.
a. Make sure that the power cord is plugged into a surge suppressor and that the surge suppressor is plugged into a properly grounded outlet. Use only a surge suppressor that meets all of the specifications.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the power switch located on the treadmill frame near the power cord. If the switch protrudes as shown, the switch has tripped. To reset the power switch, wait for five minutes and then press the switch back in.
The
power turns off during use
a.
Check the power switch (see the drawing above). If the switch has tripped, wait
for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.
c. Remove the key from the console, and then reinsert it.
d. If the treadmill still will not run, please see the front cover of this manual.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.
c. Remove the key from the console, and then reinsert it.
d. If the treadmill still will not run, please see the front cover of this manual.
The
console screen remains lit when you remove the key from the console
a. The console features a display demo mode, designed to be used if the treadmill is displayed in a store. If the screen shows a demo presentation when you remove the key, the demo mode is turned on. To turn off the demo mode.
The incline of the treadmill does not change correctly
a. Calibrate the incline system
The iFit mode does not function correctly
a. If the iFit mode is not functioning correctly, make sure that the treadmill has the most current firmware available
The treadmill will not connect to the wireless network
a. Make sure that the wireless settings on your console are correct
b. Make sure that the settings for your wireless network are correct.
c. If you still have questions, see the front cover of this manual.
a. The console features a display demo mode, designed to be used if the treadmill is displayed in a store. If the screen shows a demo presentation when you remove the key, the demo mode is turned on. To turn off the demo mode.
The incline of the treadmill does not change correctly
a. Calibrate the incline system
The iFit mode does not function correctly
a. If the iFit mode is not functioning correctly, make sure that the treadmill has the most current firmware available
The treadmill will not connect to the wireless network
a. Make sure that the wireless settings on your console are correct
b. Make sure that the settings for your wireless network are correct.
c. If you still have questions, see the front cover of this manual.
The
walking belt slows when walked on
a. Use only a surge suppressor that meets all of the specifications.
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG
THE POWER CORD. Using the hex key, turn both idler roller screws counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.
a. Use only a surge suppressor that meets all of the specifications.
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG
THE POWER CORD. Using the hex key, turn both idler roller screws counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.
c.
Your treadmill features a walking belt coated with high-performance lubricant.
The
walking belt is off-center or slips when walked on
a. If the walking belt is off-center, first remove the key and UNPLUG THE POWER CORD. If the walking belt has shifted to the left, use the hex key to turn the left idler roller screw clockwise ½ of a turn; if the walking belt has shifted to the right, turn the left idler roller screw counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is centered.
a. If the walking belt is off-center, first remove the key and UNPLUG THE POWER CORD. If the walking belt has shifted to the left, use the hex key to turn the left idler roller screw clockwise ½ of a turn; if the walking belt has shifted to the right, turn the left idler roller screw counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is centered.
b.
If the walking belt slips when walked on, first remove the key and UNPLUG THE
POWER CORD. Using the hex key, turn both idler roller screws clockwise, 1/4 of
a turn. When the walking belt is correctly tightened, you should be able to
lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking
platform. Be careful to keep the walking belt centered. Then, plug in the power
cord, insert the key, and carefully walk on the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
MAINTENANCE
MODE
1. Select the settings main menu.
2. Select the maintenance mode.
In the settings main menu, touch the Maintenance button to enter the maintenance mode.
The maintenance mode main screen will show information about the model and version of the treadmill.
1. Select the settings main menu.
2. Select the maintenance mode.
In the settings main menu, touch the Maintenance button to enter the maintenance mode.
The maintenance mode main screen will show information about the model and version of the treadmill.
Calibrate
the incline system of the treadmill.
Touch the Calibrate Incline button. Then, touch the Begin button to calibrate the incline system.
The treadmill will automatically rise to the maximum incline level, lower to the minimum incline level, and then return to the starting position. This will calibrate the incline system. Press the Cancel button to return to the maintenance mode. When the incline system is calibrated, touch the Finish button.
IMPORTANT: Keep pets, feet, and other objects away from the treadmill while the incline system is calibrating. In an emergency, pull the key from the console to stop the incline calibration.
Touch the Calibrate Incline button. Then, touch the Begin button to calibrate the incline system.
The treadmill will automatically rise to the maximum incline level, lower to the minimum incline level, and then return to the starting position. This will calibrate the incline system. Press the Cancel button to return to the maintenance mode. When the incline system is calibrated, touch the Finish button.
IMPORTANT: Keep pets, feet, and other objects away from the treadmill while the incline system is calibrating. In an emergency, pull the key from the console to stop the incline calibration.
Exit
the maintenance mode.
To exit the maintenance mode, touch the back but ton on the screen.
To exit the maintenance mode, touch the back but ton on the screen.
