How to remove the Battery – How to remove the
Service door – How to remove the keyboard: HP EliteBook
Revolve 810 G1
How to remove Battery
1. Turn off the computer. If you are
unsure whether the computer is off or in Hibernation, turn the computer on, and
then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
Remove the battery:
1. Turn the computer upside down on a flat surface, with the battery bay toward you.
2. Slide the battery release latch (1) to release the battery.
3. Pivot the battery up and then remove the battery from the computer (2).
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
Remove the battery:
1. Turn the computer upside down on a flat surface, with the battery bay toward you.
2. Slide the battery release latch (1) to release the battery.
3. Pivot the battery up and then remove the battery from the computer (2).
How to remove Service
cover
Before removing the service cover, follow
these steps:
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the battery (see Battery on page 33).
Remove the service cover
1. Turn the computer upside down, with the front toward you.
2. Press on the micro SD Card bezel (1) once to release the bezel, and then press on the bezel again to remove the bezel.
The micro SD Card bezel is included in the Plastics/Rubber Kit, spare part number 716744-001.
3. Remove the two large rubber screw covers (2).
4. Remove the two Phillips PM2.0×6.5 screws (3) that secure the service cover to the computer.
5. Remove the two small rubber screw covers (4).
The large and small rubber screw covers are included in the Plastics/Rubber Kit, spare part number 716744-001.
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the battery (see Battery on page 33).
Remove the service cover
1. Turn the computer upside down, with the front toward you.
2. Press on the micro SD Card bezel (1) once to release the bezel, and then press on the bezel again to remove the bezel.
The micro SD Card bezel is included in the Plastics/Rubber Kit, spare part number 716744-001.
3. Remove the two large rubber screw covers (2).
4. Remove the two Phillips PM2.0×6.5 screws (3) that secure the service cover to the computer.
5. Remove the two small rubber screw covers (4).
The large and small rubber screw covers are included in the Plastics/Rubber Kit, spare part number 716744-001.
6. Remove the two Phillips PM2.0×8.5
screws (5) that secure the service cover to the computer.
7. Loosen the four captive Phillips
screws (1) that secure the service cover to the computer.
8. Lift the front edge of the service
cover (2) until the cover detaches from the computer, and then remove
the service cover (3) from the computer.
How to remove WWAN module
Before removing the WWAN module, follow these
steps:
1. Turn off the computer. If you are unsure whether the computer is off or
in Hibernation, turn the computer on, and then shut it down through the
operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the battery
5. Remove the service cover
Remove the WWAN module
1. Disconnect the WWAN antenna cables (1) from the terminals on the WWAN module.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the battery
5. Remove the service cover
Remove the WWAN module
1. Disconnect the WWAN antenna cables (1) from the terminals on the WWAN module.
2. Remove the Phillips PM2.0×3.0
screw (2) that secures the WWAN module to the computer. (The
WWAN module tilts up.)
WWAN module tilts up.)
3. Remove the WWAN
module (3) by pulling the module away from the slot at an angle.
How to remove WLAN module
Before removing the WLAN module, follow these
steps:
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the battery
5. Remove the service cover
Remove the WLAN module:
1. Disconnect the WLAN antenna cables (1) from the terminals on the WLAN module.
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the battery
5. Remove the service cover
Remove the WLAN module:
1. Disconnect the WLAN antenna cables (1) from the terminals on the WLAN module.
2. Remove the Phillips PM2.0×3.0
screw (2) that secures the WLAN module to the computer. (The WLAN
module tilts up.)
3. Remove the WLAN
module (3) by pulling the module away from the slot at an angle.
How to remove Keyboard
Before removing the keyboard, follow these
steps:
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the battery.
5. Remove the service cover.
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the battery.
5. Remove the service cover.
Remove the keyboard
1. Loosen the 2 captive screws that
secure the keyboard to the computer.
2. Rest and secure the computer on its
left side.
3. Partially open the computer.
4. Insert a screw driver or similar thin tool into the keyboard release hole near the fan, and then press on the back of the keyboard until the keyboard disengages from the computer.
4. Insert a screw driver or similar thin tool into the keyboard release hole near the fan, and then press on the back of the keyboard until the keyboard disengages from the computer.
5. Turn the computer right-side up with
the front toward you.
6. Open the computer.
7. Lift the rear edge of the keyboard,
and then swing the keyboard up and forward until it rests upside down on the
palm rest.
8. Release the ZIF
connector (1) to which the backlight cable is attached, and then
disconnect the backlight cable (2) from the system board.
9. Release the ZIF
connector (3) to which the keyboard cable is attached, and then
disconnect the keyboard cable (4) from the system board.
10. Remove the keyboard (5).
How to remove Bottom cover
Before removing the
bottom cover, follow these steps:
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the battery
5. Remove the service cover
6. Remove the keyboard.
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the battery
5. Remove the service cover
6. Remove the keyboard.
Remove the bottom cover
1. Remove the two Phillips PM2.0×4.3
screws that secure the bottom cover to the computer.
2. Close the computer.
3. Turn the computer upside down, with
the rear toward you.
4. Disconnect the microphone cable (1) from the system board.
4. Disconnect the microphone cable (1) from the system board.
5. Release the
tape (2) and (3) that secures the WWAN antenna cables and
the WLAN antenna cables.
6. Remove the five Torx T8M2.0×5.65
screws (1) and the Torx T8M2.0×2.5 screw (2) that secure
the bottom cover to the computer.
7. Remove the bottom cover.
