PROGRAMMING DEVICE CONTROL
The C4000 Remote Control is preprogrammed to operate the cable box (converter)provided by your cable system, an RCATV, a Toshiba DVD player, and a Pioneer audio receiver. To control devices other than the default brands, perform the following steps; otherwise skip this
section.
NOTES: For control of a Combo device (for example, a TV/VCR combo), skip this section and perform the instructions on “Setting Up a Combo Unit”. Also refer to “Function Key Chart” on this page to find out which devices can be programmed onto each device key.
PROGRAMMING DEVICE CONTROL
The C4000 Remote Control is preprogrammed to operate the cable box (converter)provided by your cable system, an RCATV, a Toshiba DVD player, and a Pioneer audio receiver. To control devices other than the default brands, perform the following steps; otherwise skip this section.
NOTES: For control of a Combo device (for example, a TV/VCR combo), skip this section and perform the instructions on “Setting Up a Combo Unit”. Also refer to “Function Key Chart” on this page to find out which devices can be programmed onto each device key.
The C4000 Remote Control is preprogrammed to operate the cable box (converter)provided by your cable system, an RCATV, a Toshiba DVD player, and a Pioneer audio receiver. To control devices other than the default brands, perform the following steps; otherwise skip this
section.
NOTES: For control of a Combo device (for example, a TV/VCR combo), skip this section and perform the instructions on “Setting Up a Combo Unit”. Also refer to “Function Key Chart” on this page to find out which devices can be programmed onto each device key.
PROGRAMMING DEVICE CONTROL
The C4000 Remote Control is preprogrammed to operate the cable box (converter)provided by your cable system, an RCATV, a Toshiba DVD player, and a Pioneer audio receiver. To control devices other than the default brands, perform the following steps; otherwise skip this section.
NOTES: For control of a Combo device (for example, a TV/VCR combo), skip this section and perform the instructions on “Setting Up a Combo Unit”. Also refer to “Function Key Chart” on this page to find out which devices can be programmed onto each device key.
1. Turn
on a device and, if applicable, insert video media, (e.g., cassette or disc).
NOTE: Please read steps 2 through 4 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step 2.
2. On the remote control, press a device key once(i.e., AUX, DVD, TV, CBL, or STB); it blinks once. Then press and hold SET UP until the selected mode key blinks twice.
3. Use the “Setup Codes for Televisions” on page 2) to locate the type of device and brand name and then enter the first five-digit code for your device. If performed correctly, the selected mode key blinks twice.
NOTE: If the selected mode key emits a long blink, the entry is invalid.
Repeat steps 2 through 3 and try entering the same code again.
4. Aim the remote control at the device and press POWER once. The device should turn off. If it does not, repeat steps 2 through 3, trying each code for your brand until you find one that works. If it still does not respond, try searching for the code (see “Searching for Your Code”).
NOTE: If the device does not have a POWER key, press the 4(Play) key.
Repeat steps 1 through 4 to reach device you want the remote control to operate. For future reference, write down each working device code.SETTING UP A COMBO UNIT
If you own a combo unit such as a TV/DVD Combo or a TV/VCR Combo, you need to follow special steps to set it up. Perform the following instructions to control combo device:
1. For a TV/DVD Combo, turn on your TV/DVD Combo and insert a DVD. (For a TV/VCR Combo, insert a videocassette).
2. On the remote control, press DVD once; it blinks once. Then press and hold SET UP until the DVD key blinks twice.
3. Locate the brand name and enter the first five-digit code for your combo device (for example, TV/VCR). If you perform this procedure correctly, the DVD key blinks twice.
NOTE: If the DVD key did not blink twice after entering the code’s last digit, repeat steps 2 through 3 and try entering the same code again.
If you’ve located a setup code that works for your combo device (for example, a TV/DVD Combo) and a separate TV code is also listed, you’ll need to program this code into the remote control to access volume control (See “Programming Device Control”).
4. Aim the remote control at your combo device (for example, TV/DVD Combo) and press POWER once. The device should turn off.
If it does not respond, repeat steps 2 through 3, trying each code listed for your brand until you find one that works. If it still does not respond, try searching for the code (See “Searching for Your Code”).
NOTE: Please read steps 2 through 4 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step 2.
2. On the remote control, press a device key once(i.e., AUX, DVD, TV, CBL, or STB); it blinks once. Then press and hold SET UP until the selected mode key blinks twice.
3. Use the “Setup Codes for Televisions” on page 2) to locate the type of device and brand name and then enter the first five-digit code for your device. If performed correctly, the selected mode key blinks twice.
NOTE: If the selected mode key emits a long blink, the entry is invalid.
Repeat steps 2 through 3 and try entering the same code again.
4. Aim the remote control at the device and press POWER once. The device should turn off. If it does not, repeat steps 2 through 3, trying each code for your brand until you find one that works. If it still does not respond, try searching for the code (see “Searching for Your Code”).
NOTE: If the device does not have a POWER key, press the 4(Play) key.
Repeat steps 1 through 4 to reach device you want the remote control to operate. For future reference, write down each working device code.SETTING UP A COMBO UNIT
If you own a combo unit such as a TV/DVD Combo or a TV/VCR Combo, you need to follow special steps to set it up. Perform the following instructions to control combo device:
1. For a TV/DVD Combo, turn on your TV/DVD Combo and insert a DVD. (For a TV/VCR Combo, insert a videocassette).
2. On the remote control, press DVD once; it blinks once. Then press and hold SET UP until the DVD key blinks twice.
3. Locate the brand name and enter the first five-digit code for your combo device (for example, TV/VCR). If you perform this procedure correctly, the DVD key blinks twice.
NOTE: If the DVD key did not blink twice after entering the code’s last digit, repeat steps 2 through 3 and try entering the same code again.
If you’ve located a setup code that works for your combo device (for example, a TV/DVD Combo) and a separate TV code is also listed, you’ll need to program this code into the remote control to access volume control (See “Programming Device Control”).
4. Aim the remote control at your combo device (for example, TV/DVD Combo) and press POWER once. The device should turn off.
If it does not respond, repeat steps 2 through 3, trying each code listed for your brand until you find one that works. If it still does not respond, try searching for the code (See “Searching for Your Code”).
SEARCHING
FOR YOUR CODE
If your home entertainment device does not respond to the C4000 Remote Control after trying all of the codes listed for your brand, or if your brand is not listed at all, try searching for your code.
NOTE: Use the following device code digits to control a specific device:
0 = Cable (dedicated to cable only)
1 = TV
2 = DVD/VCR
3 = Audio
For example, to search for a code for your TV:
1. Turn on your TV.
2. On the remote control, press TV once; it blinks once. Then press and hold SET UP until the TV key blinks twice.
3. Enter 9 9 1. The TV key blinks twice.
4. Press 1 (the device code digit for your TV). The TV key blinks twice. Aim the remote control at the TV and press POWER once.
5. Press and release the CH+ key continuously, then stop when the TV turns off.
NOTE: In the search mode, the remote control sends IR codes from its library to the selected device, starting with the most popular code first.
6. Press POWER. The TV should turn on, and then press SET UP to lock in the code.
NOTE: If the TV does not turn on during step 6, then slowly press and release CH- to go back through the codes, then press SET UP when the TV turns on.
7. To search for the codes of your other devices, repeat steps 1
through 5, but substitute the appropriate key (e.g., AUX, DVD, CBL, or STB) for the device you are searching for.
If your home entertainment device does not respond to the C4000 Remote Control after trying all of the codes listed for your brand, or if your brand is not listed at all, try searching for your code.
NOTE: Use the following device code digits to control a specific device:
0 = Cable (dedicated to cable only)
1 = TV
2 = DVD/VCR
3 = Audio
For example, to search for a code for your TV:
1. Turn on your TV.
2. On the remote control, press TV once; it blinks once. Then press and hold SET UP until the TV key blinks twice.
3. Enter 9 9 1. The TV key blinks twice.
4. Press 1 (the device code digit for your TV). The TV key blinks twice. Aim the remote control at the TV and press POWER once.
5. Press and release the CH+ key continuously, then stop when the TV turns off.
NOTE: In the search mode, the remote control sends IR codes from its library to the selected device, starting with the most popular code first.
6. Press POWER. The TV should turn on, and then press SET UP to lock in the code.
NOTE: If the TV does not turn on during step 6, then slowly press and release CH- to go back through the codes, then press SET UP when the TV turns on.
7. To search for the codes of your other devices, repeat steps 1
through 5, but substitute the appropriate key (e.g., AUX, DVD, CBL, or STB) for the device you are searching for.
CHECKING THE CODES
If you have set up the C4000 Remote Control by searching for your device code, you may need to find out which five-digit code is operating your equipment.
For example, to find out which code is operating your TV:
1. On the remote control, press TV once; it blinks once. Then press and hold SET UP until the TV key blinks twice.
2. Enter 9 9 0. The TV key blinks twice.
3. To view the code for the first digit, press 1 once. Count the number of times the TV key blinks (e.g., 3 blinks = 3) and write down the number in the leftmost TV Code box above.
NOTE: If a code digit is 0, the selected mode key does not blink.
4. Repeat step 3 four more times for the remaining digits. Use 2 for the second digit, 3 for the third digit, 4 for the fourth digit, and 5 for the fifth digit. Finish writing down the code in the TV Code boxes above.
To check for othe rdevice codes ,repeat steps 1through 4,butsubstitute
the appropriate key (e.g., AUX, DVD, CBL, or STB) for the device you are checking. Write down the codes in the appropriate boxes..
PROGRAMMING CHANNEL CONTROL LOCK
By default, the remote control’s channel-control capabilities are locked to the cable converter. The affected keys are 1 through 0, CH+, CH-, and LAST. This guarantees that you do not inadvertently change a channel on your TV or VCR. However, you can de-activate this feature to allow full access to these keys in the TV and VCR modes.
Unlocking Channel Control
1. On the remote control, press CBL (or STB) once; it blinks once. Press and hold SET UP until the CBL (or STB) key blinks twice.
2. Enter 9 7 3. The CBL (or STB) key blinks twice.
3. Press CH- once. The CBL (or STB) key blinks four times.
Now the remote control provides TV and VCR channel-control capabilities while in the TV or VCR mode.
Locking Channel Control to CBL
1. On the remote control, press CBL (or STB) once; it blinks once. Press and hold SET UP until the CBL (or STB) key blinks twice.
2. Enter 9 7 3.The CBL (or STB) key blinks twice.
3. Press CH+ once. The CBL key blinks once.
4. Press CBL once. The CBL key blinks twice.
Now, regardless of what mode you select, the channel keys only change channels on your cable converter.
CHANGING
VOLUME LOCK
Volume Lock allows you to control the volume through the device identified as having your primary speaker(s), regardless of which mode you are using. On the C4000RemoteControl,Global Volume Lock is set to TV, so you can control TV volume while in the AUX, DVD, TV or CBL mode. You can perform Individual Volume Unlock on a selected device to set its volume control for independent operation.
Volume Lock allows you to control the volume through the device identified as having your primary speaker(s), regardless of which mode you are using. On the C4000RemoteControl,Global Volume Lock is set to TV, so you can control TV volume while in the AUX, DVD, TV or CBL mode. You can perform Individual Volume Unlock on a selected device to set its volume control for independent operation.
Unlocking Volume Control
for a Single Device (Individual Volume Unlock)
1. Assuming Global Volume Lock is active, select a mode on the remote control that you want to unlock (e.g., CBL) and press it once. Next, press and hold SET UP until the device key blinks twice.
2. Enter 9 9 3. The last-selected device key blinks twice.
3. Press VOL- once. The last-selected device key blinks four times.
4. Repeat steps 1 through 3 for each device you want volume to be unlocked.
Now, after you select a device that has volume unlocked (e.g., CBL), pressing VOL+, VOL-,or MUTE, controls only that device’s volume.
1. Assuming Global Volume Lock is active, select a mode on the remote control that you want to unlock (e.g., CBL) and press it once. Next, press and hold SET UP until the device key blinks twice.
2. Enter 9 9 3. The last-selected device key blinks twice.
3. Press VOL- once. The last-selected device key blinks four times.
4. Repeat steps 1 through 3 for each device you want volume to be unlocked.
Now, after you select a device that has volume unlocked (e.g., CBL), pressing VOL+, VOL-,or MUTE, controls only that device’s volume.
Unlocking All Volume Control (Global Volume Unlock)
NOTE: Performing these instructions sets independent volume control for all programmed devices.
1. On the remote control, press and hold SET UP until the last selected device key blinks twice.
2. Enter 9 9 3. The last-selected device key blinks twice.
3. Press VOL+ once. The last-selected device key blinks four times.
Locking Volume Control To One Mode (Global Volume Lock)
1. On the remote control, press and hold SET UP until the last selected device key blinks twice.
2. Enter 9 9 3. The last-selected device key blinks twice.
3. Select a mode (e.g., TV or AUX) which you want to use to control the volume. The selected device key blinks twice.
Now, when you press VOL+, VOL-,or MUTE, the volume of the selected device (e.g., TV) is controlled regardless of mode.
USING THE SYSTEM ON/OFF KEY
1. Press SYSTEM ON/OFF once. Your devices turn on or off in the pre-programmed sequence.
NOTE: Only devices you have programmed the remote to control turn on or off sequentially. For example, if you have programmed control of your TV, but not your DVD player, SYSTEM ON/OFF does not turn your DVD player on or off.
USING KEYMOVER
The C4000 Control includes a Key-mover feature that allows you to map (or copy)keys from one mode (i.e., source mode) to another mode (i.e.,destination mode).
Programming Key mover
For example, if your DVD player does not have volume control, you can map those keys (i.e., VOL+, VOL-, and MUTE) from the TV mode to DVD mode as follows:
1. On the remote control, press CBL (or STB) once; it blinks once. Then press and hold SET UP until the CBL (or STB) key blinks twice.
2. Enter 9 9 4. The CBL (or STB) key blinks twice.
3. For the source mode, press a desired device key once (i.e., AUX,TV, DVD, CBL or STB). For this example, press TV once.
4. For the source key, press a key to be moved once. For this example press VOL- once.
5. For the destination mode, press a desired device key once (i.e., AUX, TV, DVD, or CBL or STB). For this example, press DVD once.
6. For the destination key, press a key to be moved once. For this example press VOL+ once.
7. Repeat steps 1 to 6 to move additional keys. For this example, repeat steps 1 to 6 two more times to map the remaining volume control keys, substituting VOL- and MUTE as source and destination keys in steps 4 and 6.
Upon completion of the above procedure, you can now use your C4000 Remote Controls to control the TV’s volume and mute in the DVD mode, as well as in the TV mode.
Restoring
All Key mover Keys in a Single Mode
1. On the remote control, press CBL or STB once; it blinks once. Then press and hold SET UP until the CBL key blinks twice.
2. Enter 9 9 4. The CBL (or STB) key blinks twice.
3. Press and release the mode key you want to clear twice. For example, to clear all Key mover keys for the TV mode, press and release TV twice.
Restoring a Single Key mover Key
1. On the remote control, press the MODE key once.
2. Press and hold SET UP until the last-selected mode key blinks twice (for example, TV).
3. Enter 9 9 4. The mode key blinks twice.
Press and release the device key twice. For example, to clear the CH+ key in TV mode, press and release CH+ twice.
1. On the remote control, press CBL or STB once; it blinks once. Then press and hold SET UP until the CBL key blinks twice.
2. Enter 9 9 4. The CBL (or STB) key blinks twice.
3. Press and release the mode key you want to clear twice. For example, to clear all Key mover keys for the TV mode, press and release TV twice.
Restoring a Single Key mover Key
1. On the remote control, press the MODE key once.
2. Press and hold SET UP until the last-selected mode key blinks twice (for example, TV).
3. Enter 9 9 4. The mode key blinks twice.
Press and release the device key twice. For example, to clear the CH+ key in TV mode, press and release CH+ twice.
