Power
supply:
• Europe/China/Russia/India:
220-240V~,50 Hz
• Latin
America/Asia Pacific c: 110-240V~,50-60 Hz
• Power
consumption: 55 W
Subwoofer
• Output
power: 150 W RMS (30% THD)
• Impedance: 8
ohm
• Speaker
drivers: 165 mm (6,5”) woofer
• Dimensions
(WxHxD): 195 x 265 x 265mm
Speakers
• Output
power: 2 x 75 W RMS (30% THD)
• Speaker
impedance: 4 ohm
• Speaker
drivers: 1 x 63.5 mm (2.5”) full range
• Dimensions
(WxHxD): 84.5 x159 x 80mm
Check the
electrical DC resistance between the mains plug and the secondary side:
1) Unplug the
mains cord, and connect a wire between the two pins of the mains plug.
2) Set the
mains switch the “on” position (keep the mains cord unplug).
3) Measure the
resistance value between the mains plug and the front panel, controls, and
chassis bottom.
4) Repair or
correct unit when the resistance measurement is less than 1M ¡.
5) Switch the
unit “off”, and remove the wire between the two pins of the mains plug.
Be careful
during measurements in the live voltage section. The primary side of the power
supply , including the heat sink, carries live mains voltage when you connect
the player to the mains (even when the player is “off”!). It is possible to
touch copper tracks or components in this unshielded primary area, when you service
the player. Service personnel must take precautions to prevent touching this
area or components in this area. A “lighting stroke” and a stripe-marked printing
on the printed wiring board, indicate the primary side of the power supply. . Never replace modules, or components, while
the unit is “on”
Dismantling
Instructions
Step1: Remove
6 screws around the Top Cover, and then remove the Top Cover
St Step2: If it
is necessary to dismantle Loader or Front Panel, the Front door should be
removed first.
Note: Make
sure to operate gently otherwise the guider would be damaged.
Dismantle the
front door assembly carefully to avoid damage tray and the front door.
Step3:
Dismantle Front Panel, disconnect the connectors (XP4, XP8,XP12), need release
2 snaps of Front Panel & 2 snaps of bottom cabinet , then gently pull the
Panel out from the set.
Step4:
Dismantle Front Control Board,remove 5 screws.
Step5:
Dismantle Loader, disconnect the 3 connectors (XP2, XP3, XP6) aiming in the
below figure, and remove 2 screws that connects the loader and the bottom
cabinet.
Step6:
Dismantle Main Board, first disconnect 2 connectors (XP1, XP11), and then
remove 6 screws.
Step7:
Dismantle Power Board, disconnect the connectors XS703 and CN501 on Power
Board,then remove 5 screws.
Step8: Dismantle
Amplifier Board, remove screws.
Software
upgrade method:
1.Copy the bin
file as "HTS3201_XX.bin".
2. Copy the
renamed bin file(upgrade file) to the root menu of USB device.
3. Connect the
USB device to HTS, and switch to USB source;
4. If the CD
is correct, it will display the Upgrade Menu; press the PLAY key on the remote
control to start upgrade
5. After a while,
the tray will open automatically, but must not power off the player.
6. Don’t power
off, wait until the player reset automatically, the whole upgrade process may
need 2 minutes. HTS will auto standby after complete upgrade.
Read out the
software versions to confirm upgrading
Follow the
steps shows below:
SETUP—>Preference
Setup >Version Info.
While it shows
the dialog box, we can see some information like below:
For example:
Upgrade file
name： HTSxxxx/xx.bin
version:xx.xx.xx.xx
Sub-ver:xx.xx.xx.xx
Servo:
xx.xx.xx.xx
Risc:
xx.xx.xx.xx
HDCP
KEY:PASS(FAIL)
Region Code:X
8032:
xx.xx.xx.xx
[Caution: The set must not be power off during
upgrading, Otherwise the Main board will be damaged entirely.]
Region
codes
The type plate
on the back or bottom of the home theater shows which regions it supports.
Power
supply [SMPS] schematic
No comments:
Post a Comment