HP x360
310 G2: disassembling procedure
How to remove Top cover
1. Turn
off the computer. If you are unsure whether the computer is off or in Hibernation,
turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
Remove the top cover:
1. Position the computer upside-down.
2. Pry the two rear rubber feet of the bottom cover (1).
3. Pry the screw cover of the bottom cover (2).
Rubber feet and rubber screw cover are available in the Rubber Kit, spare part numbers:
Silver HP Pavilion x360 models: 809550-001
Red HP Pavilion x360 models: 809551-001
Green HP Pavilion x360 models: 809552-001
Purple HP Pavilion x360 models: 816522-001
Silver HP x360 310 G2 models: 824141-001
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
Remove the top cover:
1. Position the computer upside-down.
2. Pry the two rear rubber feet of the bottom cover (1).
3. Pry the screw cover of the bottom cover (2).
Rubber feet and rubber screw cover are available in the Rubber Kit, spare part numbers:
Silver HP Pavilion x360 models: 809550-001
Red HP Pavilion x360 models: 809551-001
Green HP Pavilion x360 models: 809552-001
Purple HP Pavilion x360 models: 816522-001
Silver HP x360 310 G2 models: 824141-001
4. Remove the nine Phillips PM2.5×6.0 screws (3) that secure the
top cover to the computer.
5. Position
the computer upright, and then open the computer as far as possible.
6. Run
a plastic, non-marking tool around the seam to disengage the top cover from the
computer.
Separate the top cover from the computer by separating and lifting up at the seam on the left side (1), top (2), and right side (3), far enough to access the keyboard and touchpad connectors on the system board.
Separate the top cover from the computer by separating and lifting up at the seam on the left side (1), top (2), and right side (3), far enough to access the keyboard and touchpad connectors on the system board.
7. Disconnect
the touch pad cable (1) and the keyboard cable (2) from the
system board, and then remove the top cover from the computer (3).
How to remove
Before
removing the Touch-pad, follow these steps:
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the bottom cover
5. Remove the battery
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the bottom cover
5. Remove the battery
Remove the Touch-pad:
1. Position the top cover upside down.
2. Remove the six broad head Phillips PM2.0×2.0 screws (1) that secure the touchpad and the bracket.
3. Lift the bracket oƫ the top cover (2).
4. Lift the touch-pad oƫ the computer (3).
1. Position the top cover upside down.
2. Remove the six broad head Phillips PM2.0×2.0 screws (1) that secure the touchpad and the bracket.
3. Lift the bracket oƫ the top cover (2).
4. Lift the touch-pad oƫ the computer (3).
How to remove hard drive
Before
removing the hard drive, follow these steps:
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the top cover
5. Disconnect the battery.
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the top cover
5. Disconnect the battery.
Remove
the hard drive:
1. Disconnect
the hard drive connector cable (1) from the system board.
2. Lift
the hard drive out of the computer (2).
How
to remove Solid-state drive (M.2)
Before
removing the solid-state drive, follow these steps:
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the bottom cover
5. Disconnect the battery.
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the bottom cover
5. Disconnect the battery.
